Stone Grenade
stone speakers
stone grenade
Updated
5 months ago
, by boAt Knowledge Base
Stone Grenade
Say hello to the boAt Stone Grenade bluetooth speakers, half the size of Grenade XL only because it’s twice as portable and IPX 6 Water Resistant. Needless to say, it’s the bomb.
Specifications
Speaker Type | Mono |
IPX Rating | IPX6 |
Driver Type | Full Range Driver |
Driver Size | 4.445 cm |
Impedance | 4 Ohms |
Sensitivity | 80dB ± 3DB |
Frequency Response | 180Hz - 20KHz |
Battery Capacity | 1200mAh |
Playback Time | 7 hours |
Charging Time | 2 Hours |
Bluetooth Version | V4.2 |
Compatibility | All Bluetooth Devices |
Bluetooth Range | 10 M |
Troubleshooting FAQs
General FAQs
Stone Grenade can connect with two Stone Grenade and virtually forge them into one speaker for a greater impact. For TWS connection:
Turn the speakers on that you require to be forged into one, both under Bluetooth mode. Only need to set one of the two units.
Long press TWS “ “ button till you hear a sound prompt, then start to pair.
A tone will be audible again with the white light turning steady, it may take a few seconds before the two speakers connect.
Activate the phone’s Bluetooth function and search for “Stone Grenade” to establish pairing
Note:Once the two units execute TWS function, they will be automatically paired again if next time they are turned on within effective range.
Disconnecting TWS – Short press TWS “ ” button for stopping the TWS function & Long press TWS “ ” button for disconnecting both TWS and Bluetooth connectivity
Yes, the speakerphone will work and, in this case, the primary speaker will be the speakerphone.
The speaker has an AUX, USB port which supports 3.5mm. Other than that, it supports Bluetooth connectivity.
Yes, one can accept calls on the speakers.
Yes, the speakerphone will work and, in this case, the primary speaker will be the speakerphone.
Yes, it can be. However, it is advised to only do so using an aux connection as Bluetooth mode might have latency issues.
Stone Grenade is compatible with SD/TF cards.Once inserted, the speaker will turn in to TF card mode and play automatically.
The LED light will flash slowly as an indicator.
Press >> to pause or play media
Press - to decrease volume
Press + to increase the volume
Press << to play next track
When in SD/TF mode, press power button to switch to Bluetooth mode and vice versa.
Power ON: Long press the power button for 3 seconds.
Power OFF: Long press the power button for 3 seconds.
Volume Up: Short press the “+” button in steps for increasing the volume.
Volume Down: Short press the “-” button in steps for decreasing the volume
Previous Track: Long press the “-” button for returning to the previous track.
Next Track: Long press the “+” button for skipping to the next track.
Short press the Play/Pause button.
Short press the play/pause button to answer/end calls.
Long press the play/pause button for rejecting incoming calls.
Short press the “Voice Assistant” button to activate the voice assistant.
Long press the play/pause button for 2 seconds.
Insert pointed insulated object (e.g. –toothpick) into the Reset Jack.
To activate voice assistant, ensure that you have it enabled on your media device (Google on android & Siri on apple devices).
Only 2 speakers of the same model can be connected in True Wireless Mode.
Ensure that you short press the “” button to turn on voice assistant.
To charge the earphone, plug one end of the Type-C charging cable with the speaker and connect the other end to a computer or wall adapter.
Charging: During charging, you could check charging status from the 4 LED white colour charging indicators:
0%-25%: 1st LED keeps solid, second light flickers, and 3rd and 4th light stay off.
26%-50%: 1st and the 2nd LED keep solid; 3rd LED flickers and 4th stays off.
51%-75%: 1st, 2nd and 3rd LED keep solid, 4th light flickers
100%: At charging 100% all 4 LEDs stay solid
Fully Charged: Once the earphones are fully charged, it is indicated by all the 4 LEDs stay solid.
To ensure maximum efficiency and battery life ensure that the speaker is not used at 100% volume at all times and that the battery is charged when it falls to 20% and below.
Yes, the speaker is not powered through the aux cable so please make sure that it is charged and powered on before using it through aux connection.
No, you cannot charge it with Micro-USB cable. It can only be charged using the Type-C cable.
Not completely, it has IPX6 certification that only protects under accidental exposure to water and is not meant to be used inside water.