1. Check if restarting the speaker resolves the issue.

2. Check if the same problem happens for different devices and media players.

3. Check if there are any obstructions between the speaker and the device- move the device at a closer range to the speaker and see if the problem still happens.

4. Try factory-resetting the device.

1. Check if restarting the device resolves the issue.

2. Check if the speaker is in AUX mode by short pressing the M button.

3. Check if you have connected the AUX cable properly and in the correct orientation on both ends.

4. Check if the problem persists even after using a different cable or different device to connect to the speaker.

1. Check if restarting the device resolves the issue.

2. Check if the charging cable connected to the speaker is not broken, use other charging cables to charge the speaker and also ensure that the charger being used is not of 9V or 12V as that will damage the speaker. The LED indicator located on the speaker remains solid to indicate that charging is in progress.

3. Check if the charging port on the speaker is damaged or not.

4. Try factory-resetting the device.

1. Check if the connected device does not have any equalizer settings applied.

2. Check if the problem still occurs if the device is moved closer and all obstacles in the middle are removed.

3. Check if the distortion of sound happens at all volumes or only at high volumes.

4. Check if the sound quality lowers at all volumes or only at high volumes.

5. Check the sound on different media players and different devices and if the distortion happens on all devices or only on specific ones.

6. Check if the problem occurs at all levels of charging or only at low charging levels.

7. Check if the speaker does not have water droplets. In case it does, use a blow dryer to dry out any water from a distance.

1. Check if restarting the device resolves the issue.

2. Fully let the speaker discharge and then charge it fully again before use.

3. Check to see if the device has been properly connected, i.e. the jack is properly inserted into the device for AUX, USB flash drive is properly functioning for USB mode, the device is properly paired for Bluetooth mode.

4. Try connecting through a different connection mode or media device.

5. Check if the device was not subject to any mishandling or exposed to direct sunlight or hazards like fire.

1. Check to see if the device has been properly charged first or not. The LED indication of the speaker will remain solid to indicate it is still being charged. This light will turn off once the speaker has been completely charged.

2. Check if the voltage of the charger is correct for the speaker or not.

3. Check by switching the speaker on manually- rotate the Power button in the clockwise direction to switch the speaker ON.

4. Check if the device was not subject to any mishandling, broken wires or exposed to direct sunlight or hazards like fire.

1. Check if the controls do not work while connected to another device.

2. Check if the device is in AUX mode because the buttons will not work in AUX mode.

3. Check if the media player being used supports such controls and if the controls do not function on call or with other media players.

4. Check if the controls have been physically damaged or exposed to any hazards.

1. Check to see the microphone is not being blocked by any dust or obstruction.

2. Check to see if the microphone is being held at the adequate distance for it to be able to pick up the voice.

3. Check if the problem still occurs if the microphone is moved closer to the speaker and all obstacles in the middle are removed.

4. Check if the microphone was not exposed to any hazards like direct sunlight or fire.

5. Check if the microphone was not exposed to water or dipped in any liquid.

6. Try factory-resetting the device.

1. Rotate the Power button in the clockwise direction to switch the speaker ON. The speaker automatically enters Bluetooth mode.

2. Alternatively, short press the M button to select the Bluetooth Mode. The display will show “BLUE”.

3. Activate the Bluetooth on your smartphone and search for “PartyPal Bang” to connect.

4. Select “PartyPal Bang” from the list of available devices. If prompted for a passkey, enter "0000".

Congratulations! PartyPal Bang speaker is now connected to your phone via Bluetooth with a voice prompt.

• Press and hold the EQ button to clear the Bluetooth connection history of the speaker and reset to factory settings.

Note: Perform the reset function if the speaker doesn’t turn off or doesn’t respond properly.

1. In Bluetooth mode, press the M button 2 times to disconnect the current connected device.

2. Search for “PartyPal Bang” on the other Bluetooth device to connect.

• Short press the M button to change the connectivity mode (BT/USB/ AUX).

• Short press the EQ button on the speaker to switch between the available preset EQ modes: E1 (boAt Signature Sound), E2 (DJ), E3 (Vocal).

1. After turning on the speaker, press and hold the button to turn on/off the RGB light effect.

2. Short press the button to switch between 6 different modes and select your preferred light effect.

• Rotate the volume dial on the speaker in the clockwise direction to increase the playback volume and rotate the dial in the anti- clockwise direction to decrease the playback volume.

1. Previous Track: Short press the << button to return to the previous track. Press and hold the << button to rewind the currently playing song.

2. Next Track: Short press the >> button to skip to the next track. Press and hold the> > button to fast forward.

● Short press the '>||' button to play/pause audio.

1. Type-C Charging Port: Connect the Type-C charging cable over here.

2. AUX Port: Connect the AUX cable here.

3. MIC: Microphone Input Port [1x6.35mm(1/4”)]

4. LED Indicator: Indicates the LED status while charging

1. Make sure the speakers are not paired with any external devices.

2. Turn on the two speakers and select Bluetooth mode (indicated as “BLUE” on the display).

3. Press and hold the Play/Pause/TWS button on one speaker to start TWS pairing; a tone prompt will confirm the pairing.

4. Once TWS is activated, the speakers will automatically pair with each other if turned on at the same time.

5. To deactivate the TWS function and unpair the speakers, press and hold the Play/Pause/TWS button on the speaker after pairing.

• Insert a USB flash drive (containing songs in MP3 format) into the USB port after turning on the speaker and it will switch to USB mode automatically.

1. Connect one end of the provided cable to the 3.5 mm AUX input of the speaker and the other to the external device; it will switch to AUX mode automatically.

2. Alternatively, short press the M button several times to select the AUX connectivity mode.

3. In AUX mode, you can control the audio playback via the media device/phone.

NOTE: In AUX mode, all the functions will work from the connected device.

1. Connect the microphones via the appropriate input then turn them on by moving their switch to the ON position. You can connect a separate compatible wired microphone to the speaker by using the microphone input port.

2. Double press the EQ button while at least one microphone is connected. The speaker displays- n → to adjust the volume of the microphones

3. Use the volume dial to choose the desired volume level while at least one microphone is connected.

4. Double press the EQ button while at least one microphone is connected. The speaker displays ‘n’ first where you can adjust the volume of the microphones. Use the volume dial to choose the desired volume level while at least one microphone is connected.

5. Wait for 2 seconds and double press the EQ button again while at least one microphone is connected and select: E → to adjust the echo effect.

1. Connect one end of the provided charging cable to the charging input and the other end to an adaptor of 5V/ 2A.

2. During charging, the LED indicator remains solid on (the speaker will fully recharge in about 4 hours). Once the speaker is fully charged, the LED indicator will turn off.

3. When the battery is low, the speaker will make 3 low battery tone prompts in 1-minute intervals.

Note:

• Before use, it is recommended to fully charge the battery.

• Please don’t use the speaker while it is charging as it may decrease the battery’s performance.

• If the battery is completely discharged, the speaker may restart. Recharge it for at least an hour before using it.

• To ensure maximum efficiency and battery life, make sure that the speaker is not used at 100% volume at all times and that the battery is charged when it falls to 20% and below.

• Yes, it does. It supports wireless Bluetooth v5.3. Use the USB port or 3.5 mm AUX-in port playback in case you don’t want to stream wirelessly. It can support up to 6 hours of playback at 50% volume.

Note: Increasing the volume to more than 50% will reduce the playback time.

• The speaker has an AUX port which supports a 3.5 mm jack, and a USB port. Other than that, it supports Bluetooth v5.3 connectivity. It does not support FM radio or TF/microSD card compatibility.

• No, PartyPal Bang does not support calling features.

• Yes, you can charge it with a Type-C cable.

• Yes, the speaker is not powered through the AUX cable. So, please make sure that it is charged and powered on before using it through AUX connection.

• No, PartyPal Bang cannot be used as a speakerphone in any connectivity mode.

• Yes, it can be. However, it is advised to only do so using an AUX connection as Bluetooth mode might have latency issues.

• No, it cannot be.

• Only 2 speakers of the same model can be connected in True Wireless Mode