1. Check if restarting the speaker resolves the issue.

2. Check if the same problem happens for different devices and media players.

3. Check if there are any obstructions between the speaker and the device- move the device at a closer range to the speaker and see if the problem still happens.

4. Try factory-resetting the device.

1. Check if restarting the device resolves the issue.

2. Check if the speaker is in AUX mode by short pressing the M button.

3. Check if you have connected the AUX cable properly and in the correct orientation on both ends.

4. Check if the problem persists even after using a different cable or different device to connect to the speaker.

1. Check if restarting the device resolves the issue.

2. Check if the speaker is in TF mode by short pressing the Mode button.

3. Check if your TF Card is functional and working on another media device.

4. Make sure that your music files are in the MP3 format on the card.

1. Check if restarting the device resolves the issue.

2. Check if the charging cable connected to the speaker is not broken, use other charging cables to charge the speaker and also ensure that the charger being used is not of 9V or 12V as that will damage the speaker. The LED indicator located on the speaker remains red to indicate that charging is in progress.

3. Check if the charging port on the speaker is damaged or not.

4. Try factory-resetting the device.

1. Check if the connected device does not have any equalizer settings applied.

2. Check if the problem still occurs if the device is moved closer and all obstacles in the middle are removed.

3. Check if the distortion of sound happens at all volumes or only at high volumes.

4. Check if the sound quality lowers at all volumes or only at high volumes.

5. Check the sound on different media players and different devices and if the distortion happens on all devices or only on specific ones.

6. Check if the problem occurs at all levels of charging or only at low charging levels.

7. Check if the speaker does not have water droplets. In case it does, use a blow dryer to dry out any water from a distance.

1. Check if restarting the device resolves the issue.

2. Fully let the speaker discharge and then charge it fully again before use.

3. Check to see if the device has been properly connected, i.e. the jack is properly inserted into the device for AUX, USB flash drive is properly functioning for USB mode, the device is properly paired for Bluetooth mode.

4. Try connecting through a different connection mode or media device.

5. Check if the device was not subject to any mishandling or exposed to direct sunlight or hazards like fire.

1. Check to see if the device has been properly charged first or not. The LED indication of the speaker will remain red to indicate it is still being charged. This light will turn blue once the speaker has been completely charged.

2. Check if the voltage of the charger is correct for the speaker or not.

3. Check by switching the speaker on manually- use the power switch to turn the speaker on.

4. Check if the device was not subject to any mishandling, broken wires or exposed to direct sunlight or hazards like fire

1. Check if the controls do not work while connected to another device.

2. Check if the device is in AUX mode because the buttons will not work in AUX mode.

3. Check if the media player being used supports such controls and if the controls do not function on call or with other media players.

4. Check if the controls have been physically damaged or exposed to any hazards.

1. Check to see the microphone is not being blocked by any dust or obstruction.

2. Check to see if the microphone is being held at the adequate distance for it to be able to pick up the voice.

3. Check if the problem still occurs if the microphone is moved closer to the speaker and all obstacles in the middle are removed.

4. Check if the microphone was not exposed to any hazards like direct sunlight or fire.

5. Check if the microphone was not exposed to water or dipped in any liquid.

6. Try factory-resetting the device.

1. Switch on the speaker with the power switch.

2. Short press the Mode or BT button on the control panel until the LED displays BT to indicate that the speaker is in Bluetooth pairing mode.

3. Activate the Bluetooth on your smartphone and search for “PartyPal 700” to connect.

4. Select “PartyPal 700” from the list of available devices. If prompted for a passkey, enter "0000". Congratulations! PartyPal 700 speaker is now connected to your phone via Bluetooth.

5. The 'ᛒ' on the LED display will stop flashing and remain constant when the two devices are paired.

6. Once paired, you can start playback from the external device.

1. Long press the EQ button on the speaker control panel to clear the Bluetooth connection history of the speaker. This will also reset the volume, EQ mode, treble & bass levels.

2. If the device is still not working, please turn off the power button & turn it back on.

Note: Perform the reset function if the speaker doesn’t turn off or doesn’t respond properly.

1. In Bluetooth mode, press the M button 2 times to disconnect the current connected device.

2. Search for “PartyPal 700” on the other Bluetooth device to connect.

1. Connect one end of the provided charging cable to the charging input and the other end to the power supply.

2. Turn off the speaker before charging. During charging, the LED indicator turns red, once the speaker is fully charged, the LED indicator will turn blue.

3. When the battery is below 20%, the speaker will make a low battery tone every 5 minutes.

Note:

• Please don’t use the speaker while it is charging as it may decrease the battery’s performance.

• If the battery is completely discharged, the speaker may restart. Recharge it for at least an hour before using it.

• Short press the Mode button to change the connectivity mode (BT/USB/ TF Card/ AUX).

1. After turning on the speaker, short press the "LED MODE" button to switch to LED effect mode. Long press the "LED MODE" button to turn the LED light effect on/off.

2. Short press "LED MODE" button on the control panel to switch between the 7 LED modes.

   1. The operation cycle is as follows-

      LED Mode1 - LED Mode2 - LED Mode3 - LED Mode4 - LED Mode5 - LED Mode6 - LED Mode7 - LED Mode1

   2. LED Mode1 to LED Mode6: Screen display remains continuously on and shows different LED light effects.

   3. LED Mode7: Screen display remains continuously on and the LED light effects turn off.

3. The speaker will power on in the same LED mode that was active when it was powered off, ensuring a consistent experience each time.

4. LED Mode Switch On/Off: Long press the LED mode button to turn off the screen display and LED lights. The screen display will activate for 10 seconds only to show the volume level change, mic volume, other features, etc. To turn all the LEDs on, long press the LED mode button.

• Turn the knob towards the right (clockwise direction) to increase the volume and turn the knob to the left (anticlockwise direction) to decrease the volume.

• Turn the knob towards the right (clockwise direction) to increase the bass and turn the knob to the left (anticlockwise direction) to decrease the bass.

1. Previous Track: Short press the Previous Track button to return to the previous track. (not applicable in AUX mode).

2. Next Track: Short press the Next Track button to skip to the next track (not applicable in AUX mode).

• Short press the Play/Pause button to play/pause audio.

1. AC Input: Connect the power cable over here.

2. TF Card Slot: Insert the TF card in this slot.

3. AUX Port: Connect the AUX cable here.

4. USB Port: Insert the USB flash drive in this slot.

5. Guitar Input: Insert the guitar cable here.

6. Mic Input 1: Insert the microphone 1 cable here.

7. Mic Input 2: Insert the microphone 2 cable here.

8. Charging LED Indicator: Indicates the LED while charging

9. Disco Ball: Disco Ball Light

1. Make sure the speakers are not paired with any external devices.

2. Turn on the two PartyPal 700 speakers you want to pair and select Bluetooth mode (shown as BT on the LED display).

3. Once the speakers are in Bluetooth Mode and your main speaker is connected to your Bluetooth device, long press the Mode button to activate TWS on the main speaker until the speaker emits a tone indicating that it has entered TWS pairing mode. You can now playback audio through the speaker.

4. Once TWS is activated, the speakers will automatically pair with each other if turned on at the same time.

5. Long press the “Mode” button to deactivate the TWS mode and unpair the speakers.

Note: Once the two units execute the TWS function, they automatically get paired again if next time they are turned on within the effective range.

• Insert a USB flash drive/ microSD/ TF card (containing songs in MP3 format) into the USB port/TF card slot and it will switch to USB/TF card mode automatically.

1. Connect one end of the provided cable to the 3.5 mm AUX input of the speaker and the other to the external device. The speaker will automatically switch to AUX mode.

2. Alternatively, short press the “Mode” button repeatedly to switch to AUX connectivity mode.

3. In AUX mode, you can control the audio playback via the media device/phone.

NOTE: In AUX mode, all the functions will work from the connected device.

1. Slide the “On/Off” button to turn the wireless microphone on/off and connect it to the speaker.

2. You can also connect up to 2 separate wired microphones to the speaker (not provided). To connect a wired microphone, turn on the power and insert the mic wire into the microphone input port on the speaker. press 3 seconds to turn the mic on and off.

3. Long press the “Play/Pause” button to activate the microphone priority function which allows you to speak with higher volume and decreases the volume of the track being played when the microphone is used.

Note: You can also connect two wireless microphones to the speaker- one wireless microphone is provided with PartyPal 700, while the second wireless microphone can be purchased separately. It must be a boAt wireless microphone, compatible with PartyPal 700.

• PartyPal 700 features a guitar jack which can be used for attaching an electric guitar.

• Short press the Disco ball light button to switch the disco lights mode, long press the button to turn the Disco lights on/ off.

• To ensure maximum efficiency and battery life, make sure that the speaker is not used at 100% volume at all times and that the battery is charged when it falls to 20% and below.

• Yes, it does. It supports wireless Bluetooth v5.3 and TF card, USB, and 3.5 mm AUX-in port playback in case you don’t want to stream wirelessly. It can support up to 6 hours of playback at 60% volume.

Note: Increasing the volume to more than 60% will reduce the playback time.

• The speaker has a TF card slot, AUX port which supports 3.5 mm jack, and a USB port. Other than that, it supports Bluetooth v5.3 connectivity. It does not support FM radio.

• No, PartyPal 700 does not support calling features.

• Yes, you can charge it with a Type-C cable.

• Yes, the speaker is not powered through the AUX cable. So, please make sure that it is charged and powered on before using it through AUX connection.

• No, PartyPal 700 cannot be used as a speakerphone in any connectivity mode.

• Yes, it can be. However, it is advised to only do so using an AUX connection as Bluetooth mode might have latency issues.

• No, it cannot be.

• Only 2 speakers of the same model can be connected in True Wireless Mode

• No, it is not.