1. The Speaker can be connected to any device with either a single headphone 3.5 mm jack or twin RCA stereo output using the appropriate connection lead.

2. Simply connect the device correctly to the AUX in port on the back of the unit and enter the AUX mode by short pressing the Power/mode button until you hear the relevant voice prompt.

3. Music from the connected device cannot be played through the speakers control board. It must be controlled from the connected device.

1. The Speaker is fitted with a media player which can play compatible music files from the USB port on the back of the unit.

2. Simply insert your USB media and the unit will automatically enter USB mode and a voice prompt can be heard.

3. Alternatively, you can select the USB mode by short pressing the Power/mode button repeatedly until you hear the relevant voice prompt.

4. You can control and scroll through the tracks using the play/pause button, previous track/station or Next track/station buttons on the front of the unit.

5. The speaker also has a memory function which means it will continue from the last played track, on the last occasion it was inserted.

1. Check to see if the device is in pairing mode, after powering it on the LED indicator will blink white.

2. Check if the speaker is in the range of
   Bluetooth (usually 10m) and if there are any obstructions in between.

3. Check if the device being connected to supports Bluetooth connections or not

4. Check if it is a passcode issue and if so enter 0000 / 1204

5. Check if the speaker being connected to does have any software issues or not – Check to forget the device on Bluetooth, update the mobile software, if it still does not work try factory resetting the device.

1. Check if restarting the device resolves the issue and if the speaker is in Aux mode by short pressing the ‘Mode’ button.

2. Check if you have connected the aux cable properly and in the correct orientation on both ends.

3. Check if the problem persists even after using a different cable or different device to connect to the speaker.

1. Fully charge the speakers internal battery before first use. Insert the USB cables provided and only connect to a suitable 5V USB power supply.

2. During charging, the LED indicator will glow red and go out when the unit is fully charged.

Note: If the speaker is used while connected to a USB power source, the indicator will always glow, even when the unit is fully charged.

1. Check if connected device does not have any equalizer settings applied.

2. Check if the problem still occurs if the device is moved closer and all obstacles in the middle are removed.

3. Check if the distortion or quality lowers at all volumes or only at high volumes.

4. Check the sound on different media players and different devices and if the distortion happens on all devices or only on specific ones.

5. Check if the problem occurs at all levels of charging or only at low charging levels.

6. Check if the speaker does not have water droplets, in case they do, use the blow dryer to dry out any water from a distance.

1. Check if restarting the speaker resolves the issue.

2. Check if the same problem happens for different devices and media players.

3. Check if there are any obstructions between the speaker and the device, move the device at a closer range to the speaker and see if it still affects it.

4. Try factory-resetting the device.

Check that the volume level isn’t turned down or off or alternatively try turning to another FM station. If you are connected to another device, ensure the volume level of the device is audible and that the device has been connected correctly.

1. Connect the microphone supplied to the back of the unit as described above and switch it on.

2. You can now sing along to your favourite music tracks whilst playing them through Bluetooth, USB, AUX in and FM modes.

3. To adjust the microphones echo/reverb, long press the previous track/station or Next track/station buttons accordingly.

Note: The microphones volume can only be controlled by the unit’s master volume and has no independent volume control.

1. With a compatible USB device connected to the unit, short press the Power/mode button until you hear the relevant voice prompt.

2. Connect the microphone jack on the back of the unit. Next, short press the Next track/station button to begin recording through the connected microphone.

3. Short press the previous track/station button to end the current recording session.

4. Short press the Play/Pause button to listen to the last recorded session.

5. To listen to all your recording sessions in order, press the power/mode button and enter normal USB playback mode. You can then scroll through the session using the play/pause, previous track/station or Next track/station buttons on the front of the unit the same as you would a normal MP3 album.

1. Check to see the microphone is not being blocked by any dust or obstruction.

2. Check to see if the microphone is being held at the adequate distance for it to be able to pick up the voice.

3. Check if the microphone was not exposed to any hazards like direct sunlight or fire.

4. Check if the microphone was not exposed to water above the resistance or dipped in any other liquid or not.

5. The microphone is not functional using the aux mode, check if the device is not in aux mode.

6. Try factory-resetting the device

Ensure the microphone is connected correctly and switched on. Also check that the unit is not in USB voice record mode.

1. Ensure your device has Bluetooth mode switched on and is discoverable. Also ensure your device is within 10m range of the unit.

2. Check to see if the device has been properly charged first or not.

3. Check if the voltage of the charger is correct for the speaker or not.

4. Check by switching the speaker on manually, press and hold the power on button for at least 3 seconds.

5. Check if the device was not subject to any mishandling, broken wires or exposed to direct sunlight or hazards like fire.

1. Check if the controls do not work while connected to another device

2. Check if the device is in aux mode because the buttons will not work in aux mode

3. Check if the media player being used supports such controls and if the controls do not function on call or other media players

4. Check if the controls have been physically damaged or exposed to any hazards

1. Check if restarting the device resolves the issue.

2. Fully let the speaker discharge and then charge it fully again before use.

3. Try connecting through a different connection mode or media device.

Ensure that you short press the “” button to turn on voice assistant