Nirvana Luxe

1. Check if restarting the speaker resolves the issue.

2. Check if the same problem happens for different devices and media players.

3. Check if there are any obstructions between the speaker and the device, move the device at a closer range to the speaker and see if it still affects it.

4. Try factory-resetting the device.

1. Check if restarting the device resolves the issue.

2. Check if the speaker is in AUX mode by short pressing the Mode button.

3. Check if you have connected the AUX cable properly and in the correct orientation on both ends.

4. Check if the problem persists even after using a different cable or different device to connect to the speaker.

1. Check if restarting the device resolves the issue.

2. Check if the charging cable connected to the speaker is not broken, use other charging cables to charge the speaker and ensure that the charger being used is not of 9V or 12V as that will damage the speaker.

3. The red LED located on the speaker will indicate if the charging is happening or not.

4. Check if the charging port on the case is damaged or not.

5. Try factory-resetting the device.

1. Check if restarting the device resolves the issue.

2. Fully let the speaker discharge and then charge it fully again before use.

3. Check to see if the device has been properly connected, i.e., the jack is properly inserted into the device for AUX mode, properly paired for Bluetooth mode with blinking white LED.

4. Try connecting through a different connection mode or media device.

5. Check if the device was not subject to any mishandling or exposed to direct sunlight or hazards like fire.

1. Check if the connected device does not have any equalizer settings applied.

2. Check if the problem still occurs if the device is moved closer and all obstacles in the middle are removed.

3. Check if the distortion or quality lowers at all volumes or only at high volumes.

4. Check the sound on different media players and different devices and if the distortion happens on all devices or only on specific ones.

5. Check if the problem occurs at all levels of charging or only at low charging levels.

6. Check if the speaker does not have water droplets; in case it does, use a blow dryer to dry out any water from a distance.

1. Check if the controls do not work while connected to another device.

2. Check if the device is in AUX mode because the buttons will not work in AUX mode.

3. Check if the media player being used supports such controls and if the controls do not function on call or with other media players.

4. Check if the controls have been physically damaged or exposed to any hazards.

1. Check to see if the device has been properly charged first or not. Solid red LED on the speaker will indicate it is still being charged. This light will turn off once the speaker has been completely charged.

2. Check if the voltage of the charger is correct for the speaker or not.

3. Check by switching the speaker on manually, press and hold the power on button for at least 3 seconds.

4. Check if the device was not subject to any mishandling, broken wires or exposed to direct sunlight or hazards like fire

1. Check to see the microphone is not being blocked by any dust or obstruction.

2. Check to see if the microphone is being held at the adequate distance for it to be able to pick up the voice.

3. Check if the microphone was not exposed to any hazards like direct sunlight or fire.

4. Check if the microphone was not exposed to water above the resistance or dipped in any liquid.

5. The microphone is not functional using the AUX mode, check if the device is not in AUX mode.

6. Try factory-resetting the device.

• Double press the M button to disconnect the current connected device.

1. Use a pointed object to prick the button inside the reset port to set the speaker to default settings.

2. The Bluetooth connection history of the speaker will be cleared and go back to the default settings.

• Short press the M button to change the connectivity mode (BT/AUX).

1. The RGB light is on when the speaker is powered on.

2. Short press the Power button to turn on the light effect, switch between the 6 different light modes, and to turn off the light effect.

1. Next Track: Long press the ‘+’ button for 3 seconds to skip to the next track.

2. Previous Track: Long press the ‘-’ button for 3 seconds to return to the previous track.

1. Volume Up: Short press the ‘+’ button in steps to increase the volume.

2. Volume Down: Short press the ‘-’ button in steps to reduce the volume to your desired level.

• Short press the Play/Pause "▶" button to play or pause a track.

1. Answer Call: Short press the Play/Pause "▶" button to accept an incoming call.

2. End Call: Short press the Play/Pause "▶" button or use the mobile phone to end aongoing call.

3. Reject Call: Long press the Play/Pause "▶" button for 3 seconds to reject an incoming call.

4. Redial: Short press the Play/Pause "▶" button 3 times to redial the last contacted number.

1. Connect the speaker to your mobile via Bluetooth.

2. Double press the Power button to activate the default voice assistant (Google voice assistant/Siri) and give your commands.

1. Power on the two Stone Arc speakers you require, all in Bluetooth mode.

2. You only need to set one of the two units.

3. Press and hold the Play/Pause button on one speaker for about 2 seconds until you hear a beep to activate TWS mode.

4. Release the ‘Play/Pause’ button and wait for a few seconds for the two speakers to connect.

5. Enable Bluetooth on your mobile phone and search for “Stone Arc” to pair.

6. Select “Stone Arc” to play music through the two paired speakers.

1. When the battery is low, the speaker will make a beep sound once every 5 minutes. After 3 such indications, the speaker will automatically switch OFF.

2. Insert the charging cable provided to charge the speaker.

3. When the speaker is in charging mode, the LED remains solid red. The LED indicator turns off once the speaker is fully charged.

Note:

Please avoid using the speaker while it is charging, as this may decrease the battery’s performance.

If the battery is completely discharged, the speaker may restart. Leave it in off state and charge it for at least an hour before using it.

1. Yes, the speaker is not powered through the AUX cable.

2. Please make sure that it is charged and powered on before using it through AUX connection.

• Yes, you can charge it with a Type-C cable.

1. To ensure maximum efficiency and battery life, ensure that the speaker is not always used at 100% volume.

2. Ensure that the battery is charged when it falls to 20% and below.

1. When the speaker is in charging mode, the LED remains solid red.

2. The LED indicator turns off once the speaker is fully charged.

3. The connection status LED indicator is used for BT pairing connection.

1. Yes, this version of our Stone Arc does support the calling feature.

2. Incoming calls can be accepted and rejected via this speaker, and it can act like a speaker phone.

1. Yes, it does.

2. It supports wireless Bluetooth v5.4 and also supports 3.5 mm AUX-in port playback in case you don’t want to stream wirelessly.

3. It can support up to 12 hours of playback at 60% volume.

Note: Increasing the volume to more than 60% will reduce the playback time.

1. The speaker has an AUX port which supports 3.5 mm jack.

2. Other than that, it supports Bluetooth v5.4 connectivity.

3. It does not support FM radio.

• Yes, the speakerphone will work, and, in this case, the primary speaker will be the speakerphone.

1. Yes, it can be.

2. However, it is advised to only do so using an AUX connection as Bluetooth mode might have latency issues.

• Only 2 speakers of the same model can be connected in True Wireless Mode.

1. The speaker does have IPX5 water protection.

2. But it only protects under accidental exposure or submersion in water and is not meant for prolonged usage inside water.