• After installing the app, follow the steps shown on the app to set up your account by entering your phone number, name, and email ID. Account setup is a one-time action.

1. Separate the left and right magnetic buds of your Rockerz Arc Plus neckband earphones. Alternate red and blue LED flashes indicate that the earphones are powered on and in pairing mode.

2. Log in to your account on the boAt Hearables app.

3. Turn on the Bluetooth on your media device and enable location permission as per the notification prompt on the app.

4. Go to the “My Devices” section on the app. Rockerz Arc Plus will show up under the list of available devices with “Ready to Pair'' status. Follow the ‘Pull down to refresh’ option on the app if the device does not show up on the list.

5. Tap the Rockerz Arc Plus name card and accept the pairing request pop-up notification on your media device by clicking on ‘OK’.

6. You can also save Rockerz Arc Plus to your Google account for fast pairing in the future by clicking on “Save” and then “Set up.

Congratulations! Rockerz Arc Plus is now connected to your media device with “Connected” status.

​

1. Pair Rockerz Arc Plus to your media device by following the pairing process.

2. Go to the “System” tab on the Hearables app.

3. Dual pairing remains ON by default for keeping Rockerz Arc Plus connected to two media devices at the same time. Under the System tab, slide the “Multipoint Connectivity/ Dual Pairing” toggle to the OFF state to deactivate dual pairing. Slide the toggle once again to ON to activate dual pairing.

Note: By default, dual pairing remains ON in Rockerz Arc Plus.

1. To reset Rockerz Arc Plus from your device, go to the Troubleshooting section “?” on the Hearables app.

2. Next, tap the “Malfunctioning” sub-header in the Troubleshooting section.

3. Click on the option “Reset My Device” and select ‘Yes’ to reset the earphones.

4. Congratulations! Your Rockerz Arc Plus has been reset.

5. Rockerz Arc Plus will now show as “Ready to Pair” in the ‘My Devices’ section of the app.

6. After performing the reset, the earphones will enter pairing mode.

7. Turn on the Bluetooth on your device and select ‘Rockerz Arc Plus’ from the list of available devices to pair.

8. (Applicable only for iOS Devices): Disconnect the earphones and then reconnect to your media device to start using Rockerz Arc Plus.

To diagnose issues related to Bluetooth connectivity, mic, speaker, and battery, use the Smart Diagnostics function of the Hearables app.

1. Tap the “Diagnose My Device” option at the bottom.

2. Follow the instructions to start the smart diagnostics process.

3. Click on “Let’s Go” to start.

4. Complete all the steps one by one to check Bluetooth connectivity, mic, speaker, and battery functions.

5. Click on ‘Done’ to finish diagnostics.

• You can view the smart guide for Rockerz Arc Plus under the “System” tab of the Hearables app. Go to the ‘User Manual’ section and tap ‘Know More’ to access the manual.

1. Check to see if the earphones are in pairing mode indicated by alternate red and blue LED flashes.

2. Check if the device is in the range of Bluetooth (usually 10m) and if there are any obstructions in between.

3. Check if it works after clearing the pairing list on the device: press and hold the EQ button and the volume down (-) button simultaneously for 5 seconds to clear the paired list of devices.

4. Check to see if the device being connected to supports Bluetooth connection.

5. Check if it is a passcode issue and if so, enter ‘0000’.

6. Check to see if the device being connected to does not have any software issues – check to forget the device on Bluetooth, and update the mobile software, if it still does not work, try factory resetting the device.

In the App :

• Run the Smart Diagnostics function of the boAt Hearables app and check whether there are issues related to Bluetooth connectivity. Please note the Smart Diagnostics function in the app can only identify issues related to the firmware and not the hardware

1. Check to see if the earphones are in pairing mode indicated by alternate red and blue LED flashes.

2. Check whether the boAt Hearables app on the media device is updated to the latest version. The app version can be checked from the Google Play Store for Android smartphones and from the App Store for iOS smartphones.

3. Follow the ‘Pull down to refresh’ option on the app if the device does not show up on the list.

4. Check if the device is in the range of Bluetooth (usually 10m) and if there are any obstructions in between.

5. Check to see if the device being connected to supports Bluetooth connection.

6. Check if the Bluetooth of the media device is turned ON.

7. Check to see if the device being connected to has no software issues.

8. Check to forget the earphones from the device’s Bluetooth paired list, update the mobile software and if it still does not work, try factory resetting the product.

9. Check whether closing the app and opening it again solves the issue.

1. Check if restarting the device resolves the issue.

2. Try factory resetting the earphones.

3. Check if the same problem happens for different devices and media players.

4. Check if there are any obstructions between the earphones and the device and clear them- move the device at a closer range to the earphones and see if this still affects it.

1. Check to pair boAt Rockerz Arc Plus to the first phone as per the usual pairing procedure- Select “boAt Rockerz Arc Plus” from the list of available Bluetooth devices and then switch off both the earphones and the Bluetooth of the first phone. After this, switch on the earphones. Then turn on the Bluetooth function of the second phone. Scan and search the earphone’s pairing name “boAt Rockerz Arc Plus” and pair it to the second phone. Then simply switch on the first phone’s Bluetooth. The earphones should reconnect to the first phone and both phones should now be paired to the earphones.

2. Check to try dual pairing with other devices to see if it works with them.

1. The boAt Hearables app shows all currently and previously paired devices in the ‘My Devices’ section.

2. Once Rockerz Arc Plus is paired to your smartphone, the status gets changed to “Connected” in the thumbnail.

3. Tap the thumbnail to check whether the earphones are connected or not. You can also check the battery level of the earphones.

1. To charge the earphones, plug one end of the provided USB Type-C cable into the earphones and connect the other end to a laptop or a wall adapter or a power bank.

2. During charging, the red LED remains solid ON

3. Once the charging is complete, red LED turns OFF

1. Check if the charging wire being used is working – check to use another charging wire or try using the wire on another device.

2. Check if the voltage of the charger is correct for the device, use only 5V/2A chargers.

3. Check if the charging is done till the red LED turns OFF.

4. Check if the battery was not tampered with or exposed to any electrical damage.

5. Check if the charging port is not clogged with dirt. If so, please clean it with a cotton swab.

6. Please check if the adapter and charging cable support fast charging.

​

In the App:

• Run the Smart Diagnostics function of the boAt Hearables app and check whether there are issues related to the earphone battery. Please note the Smart Diagnostics function in the app can only identify issues related to the firmware and not the hardware.

1. Charging through wall adapter – Specs of the adapter: 5V, 2A

2. Charging through cable/wire – Standard cable: 35 strands @0.10mm diameter/strand

3. Any other accessory can be used for charging the neckband if the above norms are followed.

Note : Before using the neckband for the first time, it is recommended to fully charge it.

1. Go to the sound settings of your phone and set the equalizer to normal/ default/ zero/ none.

2. Perform a factory reset.

3. In case the neckband have water droplets, use the blow dryer to dry out any water from a distance.

4. If the neckband are clogged with ear wax, simply clear the neckband to restore the original sound.

​

In the App :

1. Check if ‘Spatial Audio’ is turned OFF in the boAt Hearables app.

2. Check if there are speaker issues using the Smart Diagnostics function of the boAt Hearables app.

1. Check if the connected device does not have any equalizer settings applied.

2. Check using different media players and different devices and whether the volume change happens on all devices or only on specific ones.

1. Check to see if the device has been properly charged first- Solid red LED will turn off to indicate that the earphones are fully charged.

2. Check if the voltage of the charger is correct for the device- use only 5V/2A chargers.

3. Check if the device was not subject to any mishandling, broken wires or exposed to direct sunlight, or hazards like fire.

1. Unpair/Forget the device and pair it again and check if the issue gets resolved

2. Check if the controls do not work while being connected to another device.

3. Check if the media player being used supports such controls and if the controls do not function on call or with other media players.

4. Check if the controls have been physically damaged or exposed to any hazards.

1. Check if restarting the device resolves the issue.

2. Try factory resetting the device

3. Check to see that the microphone is not blocked by dust.

4. Check to see if the microphone is being held at an adequate distance for it to be able to pick up the voice.

5. Check if the microphone was not exposed to any hazards like direct sunlight or fire.

6. Check if the microphone was not exposed to water above the resistance or dipped in any liquid

In the App :

• Run the Smart Diagnostics function of the boAt Hearables app and check whether there are issues related to the earphones’ mics. Please note the Smart Diagnostics function in the app can only identify issues related to the firmware and not the hardware.

1. Check if the pairing device has the feature enabled. Google Assistant or Siri should be enabled to use this feature from your device.

2. Please follow the steps carefully- press the MFB 3 times to activate the voice assistant; this should allow Google Assistant or Siri to pop up on the media screen of the device. Though under some circumstances, this feature may or may not work on some devices which may be restricted by default.

• Through the device :

1. In pairing mode (when the blue and red LEDs flash), press and hold the EQ and Volume Down (-) buttons simultaneously for 5 seconds to clear the list of paired devices.

2. After successful factory reset: Red and blue LEDs flash alternatively for 1 second to indicate the same. Congratulations! Your Rockerz Arc Plus earphones have been Reset.

​

• Through the App :

1. To reset Rockerz Arc Plus from your device, go to the Troubleshooting section “?” on the Hearables app.

2. Next, tap the “Malfunctioning” sub-header in the Troubleshooting section.

3. Click on the option “Reset My Device” and select ‘Yes’ to reset the earphones.

4. Congratulations! Your Rockerz Arc Plus has been reset.

5. Rockerz Arc Plus will now show as “Ready to Pair” in the ‘My Devices’ section of the app.

6. After performing the reset, the earphones will enter pairing mode.

7. Turn on the Bluetooth on your device and select ‘Rockerz Arc Plus’ from the list of available devices to pair.

8. (Applicable only for iOS Devices): Disconnect the earphones and then reconnect to your media device to start using Rockerz Arc Plus.

1. Switch the earphones on; both the earphones automatically enter the Connection Mode.

2. Turn on the Bluetooth functionality on your phone/media device and scan.

3. Search for ‘Rockerz Arc Plus’ and tap on the same for pairing & connect via Bluetooth.

4. If asked for a passcode, enter the pairing code as “0000” to establish Bluetooth connectivity.

5. Once connected, solid blue LED flashes for 3 seconds to show successful pairing.

• Rockerz Arc Plus can be connected to 2 devices at once. To enable this feature, following steps are to be taken:

1. Pair Rockerz Arc Plus neckband earphones with your first media device via Bluetooth.

2. Turn off both the earphones and the Bluetooth on this device.

3. Switch on the earphones and the Bluetooth on your second media device to pair.

4. Finally, switch on the Bluetooth of the first media device again.

Congratulations! Your earphones are now connected to both your devices successfully via Bluetooth.

Note: If the earphones are not connected, try connecting to the first device manually once again to activate dual pairing.

• Press the Multifunction Button (MFB) once to answer an incoming call or end an ongoing call.

• Press the Multifunction Button (MFB) twice to reject an incoming call.

• Press the Multifunction Button (MFB) once to play or pause a track

1. While playing music, press and hold the volume down (-) button for 2 seconds to return to the previous track.

2. While playing music, press and hold the volume up (+) button for 2 seconds to jump to the next track

1. Short press the volume +/- button in steps to increase or decrease the volume respectively.

2. There will be a ‘tone’ when the sound volume reaches its maximum level

• Press the Multifunction Button (MFB) 3 times to activate Voice Assistant.

1. Low battery (<10%) : RED light blinks every 30 seconds with a tone prompt

2. Power On : Blue light is ON for 1 second

3. Power Off : Red LED blinks once

4. Pairing Mode : Red and blue LEDs blink alternatively on the earphones

5. Pairing successful (1 time indication) : Solid blue LED flashes for 3 seconds

6. If pairing not successful (In pairing mode) : If 5 minutes later, pairing is still not successful, then the red LED flashes once and the earphones will auto power off

7. Connected : Blue light flashes on both the neckband ; No LED flash when media is playing

8. Neckband Charging : Red LED remains solid on

9. Fully Charged : Red LED turns OFF

10. Playing Music : All lights are OFF (But "Connected" status will remain)

11. Factory Reset : Red and blue LEDs flash alternatively for 1 second to indicate successful reset

• ASAP™ Charge is boAt’s very own patented technology. It lets your device charge at an incredible charging speed (which may vary under some circumstances) where 10 minutes of charging can give up to 10 hours of playback time! It is recommended you follow the charging norms mentioned in the product smart guide.

• Yes

• Rockerz Arc Plus does support 65ms low latency for entertainment and casual gaming. But if you’re looking for professional gaming equipment, then Rockerz Arc Plus is not the right product.

• No

• No

• No, the voice prompts are integrated inside the earphones and as of now there is no feature to turn them off or lower their volume.

• While your neckband do have IPX4 water and sweat resistance, it is recommended that they are not submerged inside water directly or used for prolonged periods inside water like for swimming/showers, as it may lead to damage