1. Check to Pair the Rockerz 150 Pro to first phone as per usual pairing procedure, then switch it off. Then switch on the earphone again and enter pairing mode, enable Bluetooth function in second phone, find earphone’s Pairing Name “Rockerz 150 Pro" and pair to second phone per usual procedure. Switch off earphone one more time. Then simply switch on earphone, without entering pairing mode (a short press until white light comes on). The earphone should automatically re-connect to the last connected phone (which is the second phone). Then find headset “Rockerz 150 Pro" in first phone’s Bluetooth setting, select this to pair to first phone. Both phones should now be paired to the earphone.

2. Check to try dual pairing with other devices to see if it works with them.

1. Check if restarting the device resolves the issue.

2. Try factory resetting the earphones.

3. Check if the same problem happens for different devices and media players.

4. Check if there are any obstructions between the earphones and the device and clear them- move the device at a closer range to the earphones and see if this still affects it.

1. Check to see if the device has been properly charged first, till the red light turns blue.

2. Check if the voltage of the charger is correct for the device, use only 5V 2A Chargers.

3. Check if the device was not subject to any mishandling, broken wires or exposed to direct sunlight or hazards like fire

1. Check to see if the charging wire being used is working – check to use another charging wire or try using the wire on another device.

2. Check if the voltage of the charger is correct for the device, use only 5V 2A chargers(output) .

3. Check if the charging is done till the red light turns completely blue.

4. Check if the battery was not tampered with or exposed to any electrical damage.

5. Check if the charging port is not clogged with dirt. If so, please clean it with a cotton swab.

6. Please check if the adapter and charging cable support fast charging.

• Check if the connected device does not have any equalizer settings applied. If yes then change it to normal/default/none/zero.

• Check using different media players and different devices and whether the volume change happens on all devices or only on specific ones.

1. Check if connected device does not have any equalizer settings applied. If yes then change it to normal/default/none/zero.

2. Try factory resetting the device.

3. Check if the device has issues even after moving it closer to the connected device and removing any obstructions.

4. Check if the distortion or quality lowers at all volumes or only at high volumes.

5. Check using different media players and different devices and if the distortion happens on all devices or only on specific ones.

6. Check to see if the earbuds have ear wax accumulated. If so, please clean it with cotton swab and alcohol, after doing so gently blow dry it from a distance.

1. Try factory resettingthe device and check if the issue is resolved.

2. Check to see the microphone is not being blocked by any particles.

3. Check to see if the microphone is being held at the adequate distance for it to be able to pick up the voice.

4. Check if the microphone was not exposed to any hazards like direct sunlight or fire.

5. Check if the microphone was not exposed to water above the resistance or dipped in any liquid.

1. Check if the controls do not work while connected to another device

2. Check to forget the device and re-pair it.

3. Check if the media player being used supports such controls.

4. Check if the controls do not function on call or other media players

5. Check if the device was not subject to any mishandling, broken wires or exposed to direct sunlight or hazards like fire.

To perform a reset on your Rockerz 150 Pro:

NOTE: Before performing reset, clear "Rockerz 150 Pro" from the pairing device history by forgetting the device.

• Long press MFB for 10 seconds in power off mode. The blue and red LEDs flashes for 5 seconds to indicate the same. This will clear all the paired devices history from the device. .

1. When switched off, press and hold the multifunction button (MFB) for 3 seconds to switch the earphones on and put them into pairing mode. The earphones will automatically enter in pairing mode with a prompt; the blue and red LEDs will flash alternatively to indicate the same.

2. Open Bluetooth on your device and search for ‘Rockerz 150 Pro’ in the list of available devices.

3. Choose ‘Rockerz 150 Pro’ from the list and if asked, enter the pairing password ‘0000’ / ‘1234’ to establish Bluetooth connectivity.

4. Once successfully connected, the blue LED flashes every 10 seconds to indicate the same.

Note: The neckband automatically turns off after 5 mins if no connection is established within this time.

1. To enable Dual Pairing, first pair the devices separately when Rockerz 150 Pro is in ‘Pairing Mode’. Once paired, 2 devices can be connected at once.

2. Music can be played through 1 device at once. Music can be shifted from 1st device to 2nd device when Music is paused in 1st device or when 2nd device gets a call.

Note : Devices mentioned above can be mobile/laptop

• Red and blue LEDs light up automatically and enter the pairing state after flashing thrice simultaneously.

1. Short press the Multifunction Button (MFB) once to receive an incoming call. There will be a ‘tone’ and the call will get answered.

2. Short press the Multifunction Button (MFB) once to end an ongoing call. There will be a ‘tone’ and the call will get ended.

• Press Multifunction Button (MFB) 2 times in the call ring status. There will be a ‘tone’ and the call will get rejected.

• While playing music, short press the Multifunction Button (MFB) once to play/pause the music.

1. While playing music, press and hold volume (-) button for 2 seconds to move to the previous track.

2. While playing music, press and hold volume (+) button for 2 seconds to move to the next track

1. Short press the volume +/- button in steps to increase/decrease the volume.

2. There will be a ‘tone’ when the sound volume reaches its maximum or minimum

• Long press the Multifunction Button (MFB) for 2 seconds to wake up ‘Google Assistant’ for Android devices and ‘Siri’ for iOS devices. A ‘Beep’ confirms the activation of voice assistant

• Press Multifunction Button (MFB) 3 times to activate BEAST mode. A voice prompt confirms the same. Pressing MFB 3 times again deactivated BEAST mode

1. Press Multifunction Button (MFB) 2 times to activate Balance mode. A voice prompt confirms the same.

2. Pressing the Multifunction Button (MFB) 2 times again switches the EQ to Signature sound (Default mode)

• Press the MFB 3 times to activate low latency mode/BEAST mode.

• ASAP™ Charge is boAt’s very own patented technology. It lets your device charge at an incredible charging speed (which may vary under some circumstances) where 10 minutes of charging can give up to 150 minutes of playback time! It is recommended you follow the charging norms mentioned in the product smart guide.

• For the ASAP™ Charge to take place effectively, kindly charge the product with an adapter with TYPE –C 5V 3A specification.

• Rockerz 150 Pro does feature 65 ms low latency for all the entertainment needs. While gaming is still subjective though because it all depends on the media device too. It is okay for casual gaming, but not professional gaming.

• No

• No

• To charge the earphone, plug one end of the USB type-C cable into the earphones and connect the other end to a computer or wall adapter

1. Low Battery: When the remaining battery is less than 20%, ‘Low Battery’ prompt is made through the earphones every 5 minute and red LED flashes quickly every few seconds to indicate it.

2. Charging: Solid red LED indicates that the earphones are being charged. (Note: Earphone cannot/shouldn’t be turned on while charging)

3. Fully Charged: Once the earphones become fully charged, the LED gets turned off

1. Charging through wall adapter – Specs of the adapter: 5V, 2A

2. Charging through cable/wire – Standard cable: 35 strands @0.10mm diameter/strand

3. Any other accessories could be used for charging the earphones as long as the above norms are followed.

• Rockerz 150 Pro earphones are IPX5 certified which means it can withstand up to low pressure water jet spray, but it cannot withstand submerging it into the water. It is recommended not to use it during swimming sessions.