Rockerz 450 Pro

 Updated 

Rockerz 450 Pro comes with 40mm drivers and the unbeatable boAt Signature sound.

Make work and workouts more fun with a mountainous playback time of 70 hours that never gives up on you.

With charging just for 10 minutes, enjoy music and your binge sessions non stop for 10 hours!

Specifications

Headphone Type

On-Ear

Driver Type

Moving Coil Driver

Driver Size

40mm

Impedance

32 ohms

Sensitivity

-80<+/-0.1%

Frequency

2.4GHz-2.480GHz

Battery Capacity

750 mAh with Protection board

Playback Time

Up to 70 Hours (at 60% volume)

Charging Time

2-3 Hours

Standby Time

500-600 Hours

Bluetooth Version

V5.0

Compatibility

All Bluetooth Devices

Bluetooth Range

10 Meters

Buttons and Indicators

Troubleshooting FAQs

Charging

Insert one end of a USB Type-C charging cable into the Type-C port of the headphone and connect the USB- ‘A’ end to a 5V, 2A rated power adapter or power bank or a computer.

The left earcup’s LED turns into red colour while charging, whereas it turns off once the headphone gets fully charged.

Note:

While charging, the headphone cannot be powered on or used.

If the headphone is connected to a computer for charging, the time taken to charge the headphone would be higher.

  1. Check to see if the Type-C charging cable being used is working and are of specification mentioned in the manual.

  2. Check the charging of the headphone by using another Type-C charging cable or try using the same type-C charging cable on another device to determine if the charging cable is faulty or not.

  3. Check if the specification (voltage/current) of the charger is correct for the device or not. A 5V, 2A charger should be used to charge the headphone.

  4. Check if the charging is done till the red LED turns completely green on the left earcup of the headphone.

  5. Check if the headphone/battery was not tampered with or exposed to any electrical damage.

  6. Check if the charging port is not clogged with dirt. If so, please clean it with a cotton swab or blow dry it to remove any clogged dirt.

  7. Check if the pin of the Type-C charging port is tampered with or damaged or any liquid damage is present or not.

Poor Sound Quality

  1. Check if connected device does not have any equalizer settings applied or not. If applied then change the equalizer setting to standard/normal and then check the sound of the headphone again.

  2. Check if the device is in the range of Bluetooth (10m) and if there are any obstructions in between the headphone and the media device or not.

  3. Check if the device has issues even after moving it closer to the connected device and removing any obstructions.

  4. Check if the distortion or quality lowers at all volumes or only at high volumes.

  5. Check the sound quality on different media players and different devices and if the distortion happens on all devices/media players or only on specific ones.

  6. Check to see if the earcups have ear wax accumulated or not. If so, please clean it with cotton swab and mild alcohol, after doing so gently blow dry it from a distance.

  1. Check if connected media device is having any equalizer settings applied or not. If applied then change the equalizer setting to standard/normal and then check the sound of the headphone again.

  2. Check if the issue is occurring on different media players and in different devices or only in a single device or media player.

  3. Check if connected device does not have any equalizer settings applied.

  4. Check if the device was not subject to any mishandling, broken wires or exposed to direct sunlight or hazards like fire and liquid.

  5. Check if the buttons are not stuck between the control board and port. Use a tooth pick to pick out the button to bring it back to position.

Bluetooth Connectivity

  1. Press & hold the Power button to switch the speakers ON.

  2. There will be a prompt as well as the rapid blinking of the mentioned LED indicator light. 

  3. Turn ON the Bluetooth function of your device and search for “Rockerz 450 Pro” in the list of available devices. 

  4. Choose “Rockerz 450 Pro” from the list and if asked then enter the pairing password ‘0000’ to establish Bluetooth connectivity.

  5. After successful pairing, the speaker is now ready to play music from your device.

  6. The speaker will automatically get connected to this device when switched ON if it is in range and the Bluetooth mode is ON.

  1. Check if the issue is occurring on different media players and in different devices or only in a single device or media player.

  2. Check if connected device does not have any equalizer settings applied.

  3. Check if the device was not subject to any mishandling, broken wires or exposed to direct sunlight or hazards like fire and liquid.

  4. Check if the buttons are not stuck between the control board and port. Use a tooth pick to pick out the button to bring it back to position.

While connected to a media device, short pressing the Bluetooth button would result in disconnecting the headphone from the media device.

  1. Check to pair the Rockerz 450 Pro to first phone per usual pairing procedure, then switch it off. Then switch ON the earphone again and enter pairing mode, enable Bluetooth function in second phone, find earphone’s Pairing Name “Rockerz 450 Pro’" and pair to second phone per usual procedure.

  2. Switch off earphone one more time. Then simply switch on earphone, without entering pairing mode (a short press until white light comes on). The earphone should automatically re-connect to the last connected phone (which is the second phone). Then find headset “Rockerz 450 Pro" in first phone’s Bluetooth setting, select this to pair to first phone. Both phones should now be paired to the earphone.  

  3. Check to try dual pairing with other devices to see if it works with them. 

Dysfunctional Voice Assistant

  1. Check if the pairing device has the feature enabled. Google Assistant or Siri should be enabled to use this feature from your device.

  2. Touch and hold on the touchpad of the right earcup until default Voice Assistant wakes up on the media device. This should allow Google Assistant or Siri to pop up on your media screen. Though under some circumstance, this feature may or may not work on some devices which may be restricted by default.

  3. Check if the device was not subject to any mishandling, broken wires or exposed to direct sunlight or hazards like fire and liquid.

Other Functional Issues

  1. Check to see if the device has been properly charged first till the red light turns off from steady.

  2. Check if the voltage of the charger is correct for the device, use only 5V 2A Chargers.

  3. Check if the device was not subject to any mishandling, broken wires or exposed to direct sunlight or hazards like fire.

  4. Check if the earcups are inserted well into our ear canal and the volume is not at zero level

  5. Check if the cables are twisted/tangled, if so, untangle them to regain working condition.

  1. Check if the touch controls are working or not while connected to another media device.

  2. Check by forgetting the headphone in the Bluetooth settings of the media device and re-pair the headphone again with the media device.

  3. Check if the media player being used for music supports such controls present in the headphone.

  4. Check if the controls do not function on call or other media players or not.

  5. Check if the device was not subject to any mishandling, broken wires or exposed to direct sunlight or hazards like fire and liquid.

 

Microphone Functionality

Yes, Rockerz 450 Pro headphones has a dedicated mic perfect for calls and recording

  1. Check to see the microphone is not being blocked.

  2. Check to see if the microphone is being held at the adequate distance for it to be able to pick up the voice.

  3. Check if the microphone was not exposed to any hazards like direct sunlight or fire.

  4. Check if the microphone was not exposed to water above the resistance or dipped in any liquid.

  5. Check if the mic hole is not clogged with dirt of sweat. If so, use cotton swab or toothpick to clean out the port holes or a dryer to dry out any water that maybe collected.

 

General FAQs

Technology

No. Rockerz 450 Pro does not support aptX.

No. Rockerz 450 Pro does not support low latency but it can be used for casual gaming, entertainment, streaming etc.

Yes. Rockerz 450 Pro supports AAC and SBC formats.

Device Controls

Power ON:

  1. Press and hold the Multifunction button for 3 seconds. A beep prompt will confirm the same.

  2. The Red & Blue LED flashes alternately to indicate the same.

Power OFF:

  1. Press and hold the Multifunction button for 3 seconds. A beep prompt will confirm the same.

  2. The Red & Blue LED flash for 1 second before the device turns OFF.

  1. Tap the volume (+) button to increase the volume to your preference level.

  2. Tap the volume (-) button to decrease the volume to your preference level.

Press the multifunction button to play/pause music.

Tap the Multifunction button once when answering or ending a call to complete the action.

Double tap the Multifunction button to reject an incoming call.

Next Track: Press and hold the ‘+’ button to play the next track.

Previous Track: Press and hold the ‘-’ button to return to the previous track.

Double tap to connect with Google & Siri and activate the voice assistant. 

No, it is recommended that you do not perform such actions or it may void your warranty credentials and damage your product.

The Rockerz 450 Pro does not have EQ modes.

Device Charging

Rockerz 450 Pro takes 2-3H to charge. Rockerz 450 Pro supports the “ASAP Charge” feature which upon 10 minutes of charging can yield up to 10 hours of playback.

Yes, Rockerz 450 Pro wireless headphones can be charged with a mobile charger.

No, it cannot be charged via micro-USB. You need a Type-C cable to charge the Rockerz 450 Pro. It is recommended to use the one provided with the product.

No, Rockerz 450 Pro does not support wireless charging.


Water/Dust Protection

Yes. Rockerz 450 Pro is water resistant and water proof to some extent but it is advisable that you do not submerge the product inside water to avoid any mishap.