1. Check when both the earbuds are taken out of the charging case, the earbuds will enter the Connection Mode, indicated by White LED flashes.

2. If one of them fails to smart power on, to manually switch the earbuds on (Manual Power On), long touch the touch sensor for 3 seconds on both Left and Right earbuds for switching them On until a solid LED light begins to flash .

3. Place the earbuds in the charging case and then try using them again. Check if it connects automatically.

4. Check and see if hard resetting the device works

1. Check if there are any obstructions between the earbuds and the device and clear them, move the device at a closer range to the earbuds and see if it still affects it.

2. Resetting your airdopes usually resolves this issue.

To perform a reset on your Airdopes 458:

Note: Before performing a reset, go to settings and forget the device from your phone/laptop

​

1. ​Place the earbuds inside the case and let the case lid remain open

2. Long press the case reset button for 10 seconds

3. The case LED flashes white to indicate a successful factory reset

4. Take out earbuds from the case and perform a fresh connection. Congratulations, your Airdopes 458 has been reset!

5. If the issue does not get resolved then long press the Capacitive Touch Control (CTC)/ the touch sensor on both earbuds for 3 seconds to manually power ON the earbuds. The powering-On is indicated by an LED

1. Check if there are any obstructions between the earbuds and the device and clear them, move the device at a closer range to the earbuds and see if it still affects it.

2. Resetting your airdopes usually resolves this issue.

To perform a reset on your Airdopes 458:

Note: Before performing a reset, go to settings and forget the device from your phone/laptop

​

1. ​Place the earbuds inside the case and let the case lid remain open

2. Long press the case reset button for 10 seconds

3. The case LED flashes white to indicate a successful factory reset

4. Take out earbuds from the case and perform a fresh connection. Congratulations, your Airdopes 458 has been reset!

5. If the issue does not get resolved then long press the Capacitive Touch Control (CTC)/ the touch sensor on both earbuds for 3 seconds to manually power ON the earbuds. The powering-On is indicated by an LED

1. To charge the earbuds, put the earbuds into the charging case in their correct orientation.

2. Once the charging is complete, charging case automatically switches off to save power.

• To charge the case, plug one end of the cable into the case and connect the other end to a computer or a wall adapter or a power bank.

1. Check if the stickers on the charging points of the ear pods are removed or not. If not then it is to be removed and the ear pods will start charging once put inside the charging case.

2. Check if the charging cable connected to the case is not broken, use other charging cable and also ensure that the charger being used is not more than 5V 2A as that will damage the case. The LED lights located on the charging case indicate the battery status of the case.The charging gets indicated by White LED on charging case. Once fully charged, all the LED will turn off.

3. Please ensure that the charging port is not damaged.

1. Ensure that the earphone case is charged for charging the earbuds.

2. Check to see if the earbuds have been put inside the case in the right orientation, and a white light on the earbuds will indicate they are still being charged. This light will go off once the earbud’s have been completely charged.

3. Clean the magnetic charging pins on the case and on the earbuds with a clean cloth dipped in mild alcohol, apply a medium pressure while cleaning and check the charging of the earbuds again.

4. After cleaning, put both the earbuds into the case in desired orientation and close the lid.

5. Once both the earbuds are charged, the LED on the case will go off.

1. Go to the sound settings of your phone and set the equalizer to normal/ default/ zero/ none.

2. Perform a factory reset.

3. In case the earbuds have water droplets, use the blow dryer to dry out any water from a distance.

4. If the earbuds are clogged with ear wax, simply clear the earbuds to restore the original sound.

5. If your device still does not get fixed then perform a factory reset

1. Check to see if the device has been properly charged first, A White light on the earbud’s will indicate they are still being charged. This light will turn off once the earbud’s have been completely charged.

2. Check if the voltage of the charger is correct for the charging case and if the lights on the bottom are glowing to indicate the charge level.

3. Check by switching on the earbud’ on manually, press and hold the capacitive touch control for 3 seconds until the LED begins to flash in red and blue.

4. Check if the device was not subject to any mishandling, broken wires or exposed to direct sunlight or hazards like fire

1. Check if the controls do not work while connected to another device

2. Check if the media player being used supports such controls and if the controls do not function on call or other media players

3. Ensure that the controls have not been physically damaged or exposed to any hazards.

4. Check if the control area has some sweat and oil as that might interfere with the capacitive touch control and clean the control area to remove any oil or sweat and the touch control should start working.

1. Check if restarting the device resolves the issue.

2. Try factory resetting the device

3. Ensure that the connected device is within the Bluetooth range (10m) and there is no obstruction between the airdopes and the connected device

4. If sweat or water has gone inside the microphone then try to clean it with a cotton swab dipped in mild alchohol.

1. Make sure that you have paired the Airdopes at least once to the device that you are trying to use IWP with before.

2. Check if Bluetooth is turned on for your media device and it has the Airdopes in the list of paired devices.

3. Try factory-resetting the device.

4. Check if your Airdopes battery case has charging in it to have IWP functioning.

To perform a reset on your Airdopes 458:

Note: Before performing a reset, go to settings and forget the device from your phone/laptop

1. Place the earbuds inside the case and let the case lid remain open

2. Long press the case reset button for 10 seconds

3. The case LED flashes white to indicate a successful factory reset

4. Take out earbuds from the case and perform a fresh connection

1. Please note that both the earbuds can be used in mono mode. Use either of the two options: Smart Power On or Manual Power On for switching on the earbud

2. The selected earbud will automatically enter the connection mode indicated by rapid white LED flashes

3. Turn on Bluetooth on your phone/media device and search for “Airdopes 458”

• Long touch the CTC of left earbud for 3 secs to activate the voice assistants such as Google Assistant or Siri

1. Answer Call : Single tap on the CTC of either of the earphones once, would result in answering an incoming call

2. End/Reject Call: Double tap the CTC of either of the earphones would result in ending or rejecting incoming calls

• Long touch for 3 seconds on the right earbud’s CTC will activate low latency BEAST mode infused with Spatial Bionic Sound. Long touch for 3 seconds again on the right CTC to deactivate BEAST mode with Spatial Bionic Sound

1. Via In-Ear Detection (Put on to play; remove to pause)

2. While playing music, single tap on the left/right CTC results in pause and another tap will result in play

1. Previous Track: While playing music, double tap on the left earbud’s CTC would result in returning to the previous track

2. Next Track: While playing music, double tap on the right earbud’s CTC would result in jumping to the next track

1. Our IWP technology allows the earbuds to connect to your phone if they have already been paired before instantaneously upon opening the case.

2. Simply open the case and ensure that the Bluetooth is turned on for your media device, the buds will connect as soon as the case is opened without the need to take them out of the case first.

• Yes. Airdopes 458 has dual microphones.

• Airdopes 458 wireless earbuds offer battery backup of up to 30 hours in total.

• Yes. Airdopes 458 comes with Environmental Noise Cancellation feature.

• The Airdopes 458 does support low latency for entertainment and casual gaming. But if you’re looking for a professional gaming equipment, then Airdopes 458is not the right product.

• Yes. Airdopes 458 does not support fast charging as it comes with ASAP charge feature.

• Yes, Airdopes 458 is IPX5 Dust and Water resistant. You can use it for your workouts or carry them along on long trips.