1.Check when both the earbuds are taken out of the charging case, the earbuds will enter into the Connection Mode, indicated by light blue LED flashes.

2.If one of them fails to smart power on, to manually switch the earbuds on (Manual Power On), long touch the CTC for 3 seconds on both Left and Right earbuds for switching them on until the LED light begins to flash in red and white colours.

3.Place the earbuds in the charging case and then try using them again. Check if it connects automatically.

4.Check and see if hard resetting the device work as desired or not.

5.Check if the earbuds are charging or not. If not then clean the earbuds and the charging case specially the charging pins and connectors with mild alcohol swab and see if it goes in charging mode or not.

1.Check if restarting the device resolves the issue.

2.Check if the same problem happens for different devices and media players.

3.Check if there are any obstructions between the earbuds and the device and clear them, move the device at a closer range to the earbuds and see if it still affects it.

4.Try factory-resetting the device.

​

​Simply the earbuds back in to the case and take them out or perform the factory reset.

​

To charge the case, plug one end of the cable into the case and connect the other end to a computer or a wall adapter or a power bank.

1.To charge the earbuds, put the earbuds into the charging case in their correct orientation.

2. A solid White LED will indicate that the earbuds are being charged. Once fully charged, the LED indicator goes off.

3. Once the earbuds are fully charged, the charging case automatically switches off to save power.​

Note: Before using the earbuds for the first time, it is recommended to fully charge the earbuds. Also, please keep the lid of the charging case closed. While charging and use a 5V/2A adaptor.

1. Check if the stickers on the charging points of the ear pods are removed or not. If not then it is to be removed and the ear pods will start charging once put inside the charging case.

2. Check if the charging cable connected to the case is not broken, use other charging cable and also ensure that the charger being used is not of 9V or 12V as that will damage the case. The LED lights located on the charging case indicate the battery status of the case.

1.Ensure that the earphone case is charged for charging the earbuds.

2.Check to see if the earbuds have been put inside the case in the right orientation, and a white light on the earbuds will indicate they are still being charged. This light will go off once the earbud’s have been completely charged.

3.Clean the magnetic connector pins on the case and connector pins on the earbuds with a clean cloth with mild alcohol and check the charging of the earbuds again

4.After cleaning, put the left earbud into the case in desired orientation and close the lid.

5.After cleaning, put the right earbud into the case in desired orientation and close the lid.

6.Once both the earbuds are charged, the LED on the case will go off.

1.Check if the charging pins of the case are clear and there is no obstruction.

2.Check if the charging pin of the earbuds are clear and there is no obstruction.

3.Check if the orientation of the earbuds inside the case is correct and they have been properly inserted inside the case.

4.Check if the pogo pins are clean. You may do so by gently cleaning it cotton swabs with alcohol.

1.Check if connected device does not have any equalizer settings applied.

2.Check if the problem still occurs if the device is moved closer and all obstacles in the middle are removed.

3.Check if the distortion or quality lowers at all volumes or only at high volumes.

4.Check the sound on different media players and different devices and if the distortion happens on all devices or only on specific ones.

5.Check if the problem occurs at all levels of charging or only at low charging levels.

6.Check if the earbuds do not have water droplets, in case they do, use the blow dryer to dry out any water from a distance.

7.Check if the earbuds are clogged with ear wax, simply clear the earbuds to restore the original sound. 

1.Check if connected device does not have any equalizer settings applied.

2.Check if the problem still occurs if the device is moved closer and all obstacles in the middle are removed.

3.Check if the distortion or quality lowers at all volumes or only at high volumes.

4.Check the sound on different media players and different devices and if the distortion happens on all devices or only on specific ones.

5.Check if the problem occurs at all levels of charging or only at low charging levels.

6.Check if the earbuds do not have water droplets, in case they do, use the blow dryer to dry out any water from a distance.

7.Check if the earbuds are clogged with ear wax, simply clear the earbuds to restore the original sound.

​

​

Long tap and hold the CTC on either earbud for 3 seconds to activate the voice assistant.

Single press the CTC on either earbud to answer an incoming call and once again to hang up an ongoing call.

​Note: The earbuds come equipped with the ENx Technology to cut down the ambient noise and lets you be heard crystal clear over voice call.

Long press the CTC for 2 seconds to reject incoming calls. 

1. While playing music, double tap on the left earbud’s CTC would result in returning to the previous track.

2. While playing music, double tap on the right earbud’s CTC would result in jumping to the next track​

While playing music, double tap on the left earbud’s CTC would result in returning to the previous track.

While playing music, double tap on the right earbud’s CTC would result in jumping to the next track.

Note: Volume cannot be controlled via earbuds and can only be adjusted via phone/media device.

Step 1: Please note that both the earbuds can be used in mono mode. Use either of the two options; Smart Power On or Manual Power On for switching on the desired earbud.

Step 2: The selected earbud will automatically enter the connection mode indicated by alternating Green and Red LED flashes. 

Step 3: Turn on Bluetooth on your phone/media device and search for ‘Airdopes 452' to connect.

​Notes: To switch to Stereo mode, simply take out the other earbud from the case. It will automatically power on and pair with the previously selected earbud, hence enabling Stereo usage.You cannot skip tracks or return to the previous tracks in Mono mode.

1.Check to see if the device has been properly charged first or not. A blue light on the earbuds will indicate they are still being charged. This light will go off once the earbud’s have been completely charged.

2.Check if the voltage of the charger is correct for the charging case and if the lights on the bottom are glowing to indicate the charge level.

3.Check by switching the earbuds on manually, press and hold the capacitive touch control for 2 seconds until the LED begins to flash in blue.

4.Check if the device was not subject to any mishandling, broken wires or exposed to direct sunlight or hazards like fire.

5.Check if the charging pins of the case and earbuds have some dirt accumulation or corrosion and clean them with alcohol swab and then put them back in the case for charge and the earbuds should start charging.

1.Check if the controls do not work while connected to another device

2.Check if the media player being used supports such controls and if the controls do not function on call or other media players

3.Check if the controls have been physically damaged or exposed to any hazards.

4.Check if the control area has some sweat and oil as that might interfere with the capacitive touch control and clean the control area to remove any oil or sweat and the touch control should start working.

1.Check if restarting the device resolves the issue.

2.Check if dust or ear wax as accumulated near or inside the microphone port, there is no blockage on the microphone.

3.Check if sweat or water has gone inside the microphone.

4.Check if there are any obstructions between the earbuds and the device and clear them, move the device at a closer range to the earbuds and see if it still affects it.

1.Check if restarting the device resolves the issue.

2.Place the earbud’s in the charging case and then try using them again.

3.Try factory-resetting the device.

1.Make sure that you have paired the Airdopes at least once to the device you are trying to use IWP with before.

2.Check if Bluetooth is turned on for your media device and it has the Airdopes in the list of paired devices.

3.Try factory-resetting the device.

4.Check if your Airdopes battery case has battery in it to have IWP functioning.

There is no special process to enable IWP, simply follow the steps to pair your Airdopes to your media device first, then upon subsequent usage the IWP tech will be enabled automatically and the Airdopes will pair automatically to your previously paired media device if Bluetooth is turned on your media device.

The earbuds come equipped with the ENx Technology to cut down the ambient noise and lets you be heard crystal clear over voice call.

No. Airdopes 452 does not support aptX codec by Qualcomm.

No. The volume cannot be controlled via earbuds and can only be adjusted via phone/media device.

Beast mode is meant to use for entertainment purposes like gaming / streaming of video / movies etc. It controls the latency of the earbuds synced with your device to make it best suitable for entertainment use. It considerably lessens the lag between the device and earbuds.

Tap on the left earbud’s CTC four times to activate Beast Mode and again four times tap to turn it off.

Yes, Airdopes 452 are IPX4 Sweat and Water resistant.