Airdopes 207

• Check if restarting the device resolves the issue.

• Check if there are any obstructions between the earbuds and the device and clear them, move the device at a closer range to the earbuds and see if it still affects it.

• Resetting your airdopes usually resolves this issue.

​

To perform a reset on your Airdopes 207:

NOTE: Before performing reset, clear "Airdopes 207" from pairing device history by forgetting device

1. Take out the earbuds from the charging case, and long touch CTCs for 5 seconds on both the earbuds.

2. Place the earbuds inside the Case (Earbuds will automatically power-off in the charging case).

3. Close the lid, wait for 5 seconds. After successful factory reset, Red LED blinks quickly 5 times on Case and Earbuds.

4. Take out the earbuds from the charging case and perform a fresh connection.

Note: To complete the factory reset, all the above steps should be performed.

1. To charge the earbuds, put the earbuds into the charging case in their correct orientation.

2. During charging, LED stays solid red

3. Once the charging is complete, charging case automatically switches off to save power and LED indicator turns off

• To charge the case, plug one end of the cable into the case and connect the other end to a computer or a wall adapter or a power bank.

• Check to see if the wire connected to the case is not broken, use other wires and ensure that the charger being used is not of 9v or 12v as that will damage the case, The LED lights located on the charging case indicate the battery status of the case.

• To charge the case, plug one end of the provided cable into the case and connect the other end to a computer or a wall adapter. A Red LED indicates charging and Red LED stays solid on indicate full charge

Note: The LED indicator located on the charging case indicate the battery status of the case. The charging gets indicated by Red LED on charging case. Once fully charged, all the LED remain solid.

1. Ensure the Airdopes case is charged for charging the earbuds.

2. Check to see if the earbuds have been put inside the case in the right orientation. Once the earbuds have been completely charged, the case LED flashes blue for 5 seconds.

3. Clean the magnetic charging pins on the case and on the earbuds with a clean cloth dipped in mild alcohol, apply a medium pressure while cleaning and check the charging of the earbuds again.

4. After cleaning, put both the earbuds into the case in desired orientation and close the lid.

1. Before using the earbuds for the first time, please fully charge the earbuds with the charging case lid being closed.

2. Charging through wall adapter – Specs of the adapter: 5V, 2A

3. Charging through cable/wire – Standard cable: 35 strands @0.10mm diameter/strand

4. Any other accessories could be used for charging the earphones if the above norms are followed.

1. Go to the sound settings of your phone and set the equalizer to normal/ default/ zero/ none.

2. Perform a factory reset.

3. In case the earbuds have water droplets, use the blow dryer to dry out any water from a distance.

4. If the earbuds are clogged with ear wax, simply clear the earbuds to restore the original sound.

5. If your device still does not get fixed then perform a factory reset

1. Check to see if the device has been properly charged first, A red light on the earbuds will indicate they are still being charged. This light will turn off once the earbud’s have been completely charged.

2. Check if the voltage of the charger is correct for the charging case and if the lights on the bottom are glowing to indicate the charge level.

3. Check by switching on the earbud’ on manually, press and hold the capacitive touch control for 3 seconds until the LED begins to flash in red and blue.

4. Check if the device was not subject to any mishandling, broken wires or exposed to direct sunlight or hazards like fire

1. Check if the controls do not work while being connected to another device.

2. Check if the media player being used supports such controls and if the controls do not function on call or with other media players.

3. Check if the controls have been physically damaged or exposed to any hazards.

1. Check if dust has accumulated inside the earbuds or if there is any obstruction.

2. Check if ear wax has accumulated inside the earbuds.

3. Check if there is no damage to the tips of the earbuds and see if changing them helps.

4. Check if sweat or water has gone inside the earbuds.

1. Check if your Airdopes model has IWP™ tech integrated.

2. Make sure that you have paired the earbuds at least once before to the device you are trying to use IWP™ with.

3. Check if Bluetooth is turned on for your media device and if it has Airdopes 207 in the list of paired devices.

4. Try factory resetting the device.

• Single tap on the CTC of either of the earbuds once, would result in answering an incoming call

• Double tap the CTC of either of the earphones would result in ending or rejecting incoming calls

• While playing music, single tap on the left/right CTC results in pause and another tap will result in play

• Previous Track : While playing music, double tap on the left earbud’s CTC would result in returning to the previous track

• Next Track : While playing music, double tap on the right earbud’s CTC would result in jumping to the next track

• Volume could only be adjusted via phone/media devices

1. Please note that both the earbuds can be used in mono mode. Use either of the two options: Smart Power On or Manual Power On for switching on the desired earbud

2. The selected earbud will automatically enter the connection mode indicated by red and blue LED flashes

3. Turn on Bluetooth on your phone/media device and search for “Airdopes 207 ”

1. Switch the earbuds on; Both the earbuds automatically enter into the Connection Mode

2. Turn on the Bluetooth functionality on your phone/media device and scan

3. Search for ‘Airdopes 207 ’ and tap on the same for pairing & connect via Bluetooth

4. To switch to Stereo mode from mono, simply take out the other earbud from the case. It will automatically power on and pair with the previously selected earbud, hence enabling Stereo usage

5. You cannot skip tracks or return to the previous tracks in Mono mode

1. Triple tapping the left earbud’s CTC will active BEAST mode for gaming. Triple tap the left CTC again to deactivate BEAST mode.

2. ANC and Ambient: NA

1. Low battery (<30%) : RED blink (3 times) when the Case lid is opened

2. Power On : BLUE light is ON for 1 second on opening the Lid

3. Power Off : Red LED flashes for 1 second

4. Pairing Mode : First, the connection happens between Master and Slave, and indicates with BLUE, then enters the pairing mode with the following LED indications:

   • Master Earbud blinks RED & BLUE during pairing mode

   • Slave Earbud blinks BLUE for every 5 sec

   Note: If Master and Slave Earbuds are not connected, it will act as an independent Earbud, and on both the Earbuds, RED & Blue blinks

5. Pairing successful (1 time indication) : Solid BLUE

6. If pairing not successful (In pairing mode) : The same as Pairing mode, if 5 minutes later still cannot be pairing successful, then the Earbuds will show solid RED once and auto power off

7. Earbuds in the charging box : • In charging status, the RED light is ON

   • Full charging, the lights are OFF

8. Connected : Blue light flashes 300ms - ON and 300ms - OFF, so 3 times each minute = the 20s per times

9. Disconnected : The same as Pairing mode

10. Fully Charged : RED light is OFF

11. Playing Music : All lights are OFF (But "Connected" status will remain)

1. Our IWP™ technology allows the earbuds to connect to your phone if they have already been paired before instantaneously upon opening the case.

2. Simply open the case and ensure that the Bluetooth is turned on for your media device, the buds will connect as soon as the case is opened without the need to take them out of the case first!

• There is no special process to enable IWP™- simply follow the steps to first pair your Airdopes 207 to your media device. Then upon subsequent usage, the IWP™ tech will be enabled and the earbuds will pair automatically to your previously paired media device if Bluetooth is turned on in your media device.

• Yes

• Yes

• Airdopes 207 does support 50 ms low latency for entertainment and casual gaming. But if you’re looking for professional gaming equipment, then Airdopes 207 is not the right product

• No

• No

• Yes

• No, the voice prompts are integrated inside the earbuds and there is no provision to turn them off or lower their volume.

• While your earbuds do have IPX5 water and sweat resistance, it is recommended that they are not submerged inside water directly or used for prolonged periods inside water like for swimming/showers, as it may lead to damage.