1. Check when both the earbuds are taken out of the charging case. The earbuds will enter Connection Mode indicated by alternating red and blue LED flashes.

2. If one of them fails to smart power on, try manually switching the earbud on (Manual Power On) - long touch the CTC for 3 seconds until the LED light begins to flash blue.

3. Place the earbuds in the charging case and then try using them again. Check if it connects automatically.

4. Check and see if factory-resetting the device works.

• Check if restarting the device resolves the issue.

• Check if there are any obstructions between the earbuds and the device and clear them, move the device at a closer range to the earbuds and see if it still affects it.

• Resetting your airdopes usually resolves this issue.

​

To perform a reset on your Airdopes 161 ANC Elite :

Note: Before performing a reset, go to settings and forget the device from your phone/laptop

1. Press the CTC on both earbuds simultaneously 4 times. Red LED blinks once on the earbuds to indicate successful factory reset.

2. Close the lid after placing the earbuds within the case. Re-open it again after a few seconds.

3. Take out the earbuds from the charging case and perform a fresh connection.

Congratulations! Your Airdopes 161 ANC Elite has been reset.

1. Check to see if the wire connected to the case is not broken. Use other wires and ensure that the charger being used is not of 9V or 12V as that will damage the case.

2. To charge the case, plug one end of the provided USB Type-C cable into the case and connect the other end to a computer, power bank, wall adapter, etc.

Note: The LED located on the charging case indicates the battery status of the case. White LED blinks continuously to indicate charging and solid white LED indicates full charge.

1. Ensure the Airdopes case is charged for charging the earbuds.

2. Check to see if the earbuds have been put inside the case in the right orientation. TheWhite LED on the case remains On for 5 seconds while the earbuds are getting charged. This light will turn off once the earbuds have been completely charged.

3. Clean the magnetic charging pins on the case and on the earbuds with a clean cloth dipped in mild alcohol, apply a medium pressure while cleaning and check the charging of the earbuds again.

4. After cleaning, put both the earbuds into the case in desired orientation and close the lid.

1. Go to the sound settings of your phone and set the equalizer to normal/ default/ zero/ none.

2. Perform a factory reset.

3. In case the earbuds have water droplets, use the blow dryer to dry out any water from a distance.

4. If the earbuds are clogged with ear wax, simply clear the earbuds to restore the original sound.

5. If your device still does not get fixed then perform a factory reset

​

1. Check to see if the device has been properly charged first. The charging case white LED remains solid on for 5 seconds when the earbuds are getting charged from the case. Once the earbuds have been completely charged, the white LED on the case turns off.

2. Check if the voltage of the charger is correct for the charging case and if the white LED on the case is blinking to indicate charging.

3. Check by switching the earbuds on manually- long touch the capacitive touch control for 3 seconds and release until the LED begins to flash white.

4. Check if the device was not subjected to any mishandling, broken wires or exposed to direct sunlight or hazards like fire.

1. Check if the controls do not work while being connected to another device.

2. Check if the media player being used supports such controls and if the controls do not function on call or with other media players.

3. Check if the controls have been physically damaged or exposed to any hazards.

1. Check if restarting the device resolves the issue.

2. Try factory resetting the device

3. Ensure that the connected device is within the Bluetooth range (10m) and there is no obstruction between the airdopes and the connected device

4. If sweat or water has gone inside the microphone then try to clean it with a cotton swab dipped in mild alchohol.

1. Check if your Airdopes model has IWP™ tech integrated.

2. Make sure that you have paired the earbuds at least once before to the device you are trying to use IWP™ with.

3. Check if Bluetooth is turned on for your media device and if it has Airdopes 161 ANC Elite in the list of paired devices.

4. Try factory resetting the device.

To perform a reset on your Airdopes 161 ANC Elite:

NOTE: Before performing reset, clear "Airdopes 161 ANC Elite" from the pairing device history by forgetting the device.

1. Press the CTC on both earbuds simultaneously 4 times. Red LED blinks once on the earbuds to indicate successful factory reset.

2. Close the lid after placing the earbuds within the case. Re-open it again after a few seconds.

3. Take out the earbuds from the charging case and perform a fresh connection.

   Congratulations! Your Airdopes 161 ANC Elite has been reset.

• Single tap the CTC on either earbud to answer an incoming call.

• Double tap the CTC on either of the earbuds to end an ongoing call or reject incoming calls.

• While playing music, single tap on the left or right earbud CTC to pause or play the track.

1. While playing music, double tap on the left earbud’s CTC to return to the previous track.

2. While playing music, double tap on the right earbud’s CTC to skip to the next track.

• Volume can only be adjusted via phone/media devices

1. Please note that both the earbuds can be used in Mono mode. Use either of the two options: Smart Power On or Manual Power On for switching on the desired earbud.

2. The selected earbud will automatically enter the connection mode indicated by white LED flashes.

3. Turn on Bluetooth on your phone/media device and search for “Airdopes 161 ANC Elite” to connect.

1. Switch the earbuds on; both the earbuds automatically enter into Connection Mode.

2. This is indicated with white LED flashes on the master earbud

3. Turn the Bluetooth On functionality on your phone/media device and scan.

4. Search for ‘Airdopes 161 ANC Elite’ and tap on the same for pairing & connecting via Bluetooth.

5. To switch to Stereo mode from Mono, simply take out the other earbud from the case. It will automatically power On and pair with the previously selected earbud, hence enabling Stereo usage.

6. You can only skip to the "next track" using the right earbud in Mono/Stereo mode.

7. You can only switch to the "previous track" using the left earbud in Mono/Stereo mode.

• Long touch the left earbud CTC for 3 seconds to switch between boAt Signature Sound & Balanced Mode. By default, the boAt Signature Sound mode remains active.

• Voice Assistant cannot be activated using Airdopes 161 ANC Elite.

• Long touch the right earbud CTC for 3 seconds to toggle between ANC OFF/Ambient/ANC ON modes.

1. Low battery (<30%) : Red light blink 3 times when the case lid is opened

2. Earbuds – 30-100% charge: Blue light blinks 3 times when the case lid is opened

3. Power On : Blue light is ON for 1 second on opening the Lid

4. Power Off : Red LED is ON for 1 second when manually powered off

5. Pairing Mode : Red and blue LEDs blink alternately on the master earbud & Slave earbud blinks blue every 5 seconds

6. Pairing successful (1 time indication) : Solid blue LED for 3 seconds

7. If pairing not successful (In pairing mode) : The earbuds will show solid red light once and auto power off

8. Connected : Blue light flashes on and off alternatively for 300ms; so 3 times each minute & No LED flash when media is playing

9. Disconnected : Same as Pairing mode- Red and blue LEDs blink alternately on both the earbuds & Slave earbud blinks blue every 5 seconds

10. Earbuds Charging : White LED on case is ON for 5 seconds when lid is closed

11. Fully Charged : LED on case is OFF when lid is closed

12. Playing Music : All lights are OFF (But "Connected" status will remain)

13. Factory Reset : Red LED on the earbud blinks for 1 second after successful factory reset.

1. Our IWP™ technology allows the earbuds to connect to your phone if they have already been paired before instantaneously upon opening the case.

2. Simply open the case and ensure that the Bluetooth is turned on for your media device, the buds will connect as soon as the case is opened without the need to take them out of the case first!

• There is no special process to enable IWP™- simply follow the steps to first pair your Airdopes 161 ANC Elite to your media device. Then upon subsequent usage, the IWP™ tech will be enabled and the earbuds will pair automatically to your previously paired media device if Bluetooth is turned on in your media device.

• Yes, Airdopes 161 ANC Elite is integrated with 2 mics per earbud.

• Airdopes 161 ANC Elite does support 50 ms low latency for entertainment and casual gaming. But if you’re looking for a professional gaming equipment, then Airdopes 161 ANC Elite is not the right product

• Yes.

• Yes

1. No, the earbuds do not have any integrated volume controls on them. The volume must be controlled using your connected Bluetooth device.

2. Ensure that in the Bluetooth settings of your media device, you have enabled syncing of Bluetooth and phone volume levels otherwise you may not be able to fully control the volume of the earbuds as intended.

• No, the voice prompts are integrated inside the earbuds and there is no provision to turn them off or lower their volume.

1. To charge the earbuds, put them into the charging case in their correct orientation.

2. While charging, the white LED on the case remains solid ON for 5 seconds.

3. Once the charging is complete, charging case automatically switches off to save power and the LED indicator turns off.

• To charge the case, plug one end of the cable into the case and connect the other end to a computer or a wall adapter or a power bank.

1. Charging through wall adapter – Specs of the adapter: 5V/2A

2. Charging through cable/wire – Standard cable: 35 strands @0.10mm diameter/strand

3. Any other accessory can be used for charging the earbuds as long as the above norms are followed.

Note :

Before using the earbuds for the first time, it is recommended to fully charge the earbuds as well as the charging case. Also, keep the lid of the charging case closed while charging.

• While your earbuds do have IPX5 water and sweat resistance, it is recommended that they are not submerged inside water directly or used for prolonged periods inside water like for swimming/showers, as it may lead to damage.