Airdopes 141 Gen 2

• Check when both the earbuds are taken out of the charging case. The earbuds will enter Connection Mode indicated by alternating red and blue LED flashes.

• Place the earbuds in the charging case and then try using them again. Check if it connects automatically.

• Check and see if factory resetting the device works.

• Resetting the device usually resolves such issues. To perform a reset:

NOTE: Before performing reset, clear "Airdopes 141 Gen 2" from pairing device history by forgetting the device.

1. Open the lid of the charging case and place the earbuds within the case.

2. Long press the reset button on the charging case for 5 seconds. All four LEDs blink (3+2) 5 times on the case. Red LED blinks 5 times on the earbuds.

3. Close the case lid and wait for 5 seconds.

4. Take out the earbuds from the charging case and perform a fresh connection.

5. If the issue does not resolve through reset, then try to manually Power Off and then Power On.

If IWP™ isn't functioning:

1. Confirm that your Airdopes model has IWP™ tech integrated.

2. Make sure you have paired the earbuds at least once before to the device you are trying to use IWP™ with.

3. Check if Bluetooth is turned on for your media device and your product name is in the list of paired devices.

4. Try factory-resetting the device.

1. To charge the earbuds, put them into the charging case in their correct orientation.

2. If single/both earbuds are charging inside the case, the red LED remains solid on.

3. When both the earbuds are fully charged, the blue LED remains solid on for 30 seconds and then turns off. The charging case automatically switches off to save power.

• To charge the case, plug one end of the cable into the case and connect the other end to a computer or a wall adapter or a power bank.

1. Check to see if the wire connected to the case is not broken.

2. Use other wires and ensure that the charger being used is not of 9V or 12V as that will damage the case.

1. Check to see if the earbuds have been put inside the case in the correct orientation.

2. If single/both earbuds are charging inside the case, the red LED remains solid on.

3. Blue LED remains solid on for 30 seconds and then turns off when both earbuds have been completely charged.

4. Check if the charging pins of the case and the earbuds are clear and there is no obstruction.

5. You may clean the pogo pins by gently cleaning them using cotton swabs dipped in alcohol.

6. If nothing else works, and there is no physical damage, send the device for a replacement.

1. Charging through wall adapter – Specs of the adapter: 5V, 2A

2. Charging through cable/wire – Standard cable: 35 strands @0.10mm diameter/strand

3. Any other accessory can be used for charging the earbuds if the above norms are followed.

Note : Before using the earbuds for the first time, it is recommended to fully charge the earbuds as well as the charging case. Also, keep the lid of the charging case closed while charging.

1. Go to the sound settings of your phone and set the equalizer to normal/ default/ none/ 0.

2. Perform a factory reset.

3. If the earbuds are clogged with ear wax, simply clean the earbuds to restore the original sound.

4. In case the earbuds have water droplets, use the blow dryer to dry out any water from a distance (Caution - Prevent your product from overheating through the dryer).

1. Make sure the charging case is charged. Try to manually power on the earbuds, the powering on is indicated by LED lights on the earbuds.

2. If the earbuds do not power On, try cleaning the pogo pins (magnetic charging pins) of the earbuds with cotton dipped in alcohol swab/spirit.

3. Later, wipe it with a dry cotton to not let any moisture retain on the surface.

4. Now place the earbuds inside the charging case, shut the lid and open it after 5 seconds.

5. The earbud LEDs will start blinking as they automatically power on.

To troubleshoot control issues:

1. Check if the controls do not work while being connected to another device.

2. Check if the media player being used supports such controls and if the controls do not function on a call or with other media players.

3. Check if the controls have been physically damaged or exposed to any hazards.

1. Try restarting the device.

2. Perform a factory reset.

3. Make sure there are no objects between your earbuds and your connected device.

4. Try moving your device closer to the earbuds to see if the connection improves.

5. Look closely at the microphone hole for any dirt or earwax. If the microphone seems blocked, gently clean that area.

NOTE: Before performing a reset, clear "Airdopes 141 Gen 2" from pairing device history by forgetting the device.

1. Open the lid of the charging case and place the earbuds within the case.

2. Long press the reset button on the charging case for 5 seconds. All four LEDs blink (3+2) 5 times on the case. Red LED blinks 5 times on the earbuds.

3. Close the case lid and wait for 5 seconds.

4. Take out the earbuds from the charging case and perform a fresh connection.

• Single tap the CTC on either earbud to answer an incoming call.

• Double tap the CTC on either earbud to end an ongoing call or reject incoming calls.

• While playing music, single tap on the left or right earbud CTC to pause or play the track.

1. While playing music, double tap on the left earbud’s CTC to return to the previous track.

2. While playing music, double tap on the right earbud’s CTC to skip to the next track.

• Volume can only be adjusted via phone/media devices.

1. Please note that both the earbuds can be used in Mono mode. Use either of the two options: Smart Power On or Manual Power On for switching on the desired earbud.

2. The selected earbud will automatically enter the connection mode indicated by alternate red and blue LED flashes.

3. Turn on Bluetooth on your phone/media device and search for “Airdopes 141 Gen 2” to connect.

1. Switch the earbuds on; both the earbuds automatically enter Connection Mode.

2. Turn on the Bluetooth functionality on your phone/media device and scan.

3. Search for ‘Airdopes 141 Gen 2’ and tap on the same for pairing & connecting via Bluetooth.

4. To switch to Stereo mode from Mono, simply take out the other earbud from the case. It will automatically power on and pair with the previously selected earbud, hence enabling Stereo usage.

• Long touch the left earbud CTC for 3 seconds to activate ‘Google Assistant’ for Android devices and ‘Siri’ for iOS devices.

Case LED Indications (Non-Charging State):

1. 100%: 4 LEDs show.

2. 75%: 3 LEDs show.

3. 50%: 2 LEDs show.

4. 25%: 1 LED shows.

5. 10-15%: 1 LED fast flashes.

Case LED Indications (Charging State):

1. 0-25%: 1st LED is flashing.

2. 25-50%: 1st LED is solid on, 2nd LED is flashing.

3. 50-75%: 2 LEDs are solid on, 3rd LED is flashing.

4. 75-100%: 3 LEDs are solid on, 4th LED is flashing.

Case LED indication when Earbuds are charging from the case:

If single/both earbuds are charging inside the case, the red LED remains solid on.

When both the earbuds are fully charged, the blue LED remains solid on for 30 seconds and then turns off.

Earbuds LED Indications:

1. Low battery (<20%): Red light quickly blinks 3 times every 30 seconds on opening the lid.

2. Power ON: Solid blue light flashes for 2 seconds on opening the lid.

3. Power OFF: Solid red LED flashes for 2 seconds when powered off.

4. Pairing mode: Alternate red and blue LED flashes on the master earbud, and the slave earbud LED flashes blue once every 5 seconds.

5. Pairing successfully (1 time indication): Solid blue LED flashes for 3 seconds.

6. If pairing is not successful (In pairing mode): The earbuds will show a solid red light once and auto power off.

7. Connected: Solid blue light flashes once every 20 seconds on both the earbuds. No LED flash when the media is playing.

8. Disconnected: Same as Pairing mode.

9. Earbuds Charging: Red LED remains solid on opening the lid.

10. Fully charged: Blue LED remains solid on for 30 seconds and then turns off.

11. Playing music: All lights are OFF (But "Connected" status will remain).

Factory Reset LED Indications:

After a successful factory reset, all four LEDs blink (3+2) 5 times on the case and red LED blinks 5 times on the earbuds.

1. Our IWP™ technology allows the earbuds to connect to your phone if they have already been paired before instantaneously upon opening the case.

2. Simply open the case and ensure that the Bluetooth is turned on for your media device, the buds will connect as soon as the case is opened without the need to take them out of the case first!

• There is no special process to enable IWP™- simply follow the steps to first pair your Airdopes 141 Gen 2 to your media device. Then upon subsequent usage, the IWP™ tech will be enabled and the earbuds will pair automatically to your previously paired media device if Bluetooth is turned on in your media device.

• Yes, Airdopes 141 Gen 2 is integrated with 2 mics per earbud.

• Yes, it does.

• Airdopes 141 Gen 2 does support 65 ms low latency for entertainment and casual gaming. However, if you’re looking for professional gaming equipment, then Airdopes 141 Gen 2 is not the right product.

• No, it does not.

• No, it does not.

• No, the earbuds do not have any integrated volume controls on them. The volume must be controlled using your connected Bluetooth device.

• Yes, long touch the left earbud CTC for 3 seconds to activate ‘Google Assistant’ for Android devices and ‘Siri’ for iOS devices.

• No, the voice prompts are integrated inside the earbuds and there is no provision to turn them off or lower their volume.

• While your earbuds do have IPX4 water and sweat resistance, it is recommended that they are not submerged inside water directly or used for prolonged periods inside water like for swimming/showers, as it may lead to damage.