1.Check when both the earbuds are taken out of the charging case, the earbuds will enter into the Connection Mode, indicated by light blue LED flashes.

2.If one of them fails to smart power on, to manually switch the earbuds on (Manual Power On), long touch the CTC for 3 seconds on both Left and Right earbuds for switching them on until the LED light begins to flash in red and white colours.

3.Place the earbuds in the charging case and then try using them again. Check if it connects automatically.

4.Check and see if hard resetting the device work as desired or not.

5.Check if the earbuds are charging or not. If not then clean the earbuds and the charging case specially the charging pins and connectors with mild alcohol swab and see if it goes in charging mode or not.

1.Check if restarting the device resolves the issue.

2.Check if the same problem happens for different devices and media players.

3.Check if there are any obstructions between the earbuds and the device and clear them, move the device at a closer range to the earbuds and see if it still affects it.

4.Try factory-resetting the device.

​Simply the earbuds back in to the case and take them out or perform the factory reset.​

​

1.To charge the earbuds, put the earbuds into the charging case in their correct orientation.

2. A solid Red LED will indicate that the earbuds are being charged. Once fully charged, the LED indicator goes off.

3. Once the earbuds are fully charged, the charging case automatically switches off to save power.​

Note: Before using the earbuds for the first time, it is recommended to fully charge the earbuds. Also, please keep the lid of the charging case closed. While charging and use a 5V/2A adaptor.

1. Check if the stickers on the charging points of the ear pods are removed or not. If not then it is to be removed and the ear pods will start charging once put inside the charging case.

2. Check if the charging cable connected to the case is not broken, use other charging cable and also ensure that the charger being used is not of 9V or 12V as that will damage the case. The LED lights located on the charging case indicate the battery status of the case.

1.Ensure that the earphone case is charged for charging the earbuds.

2.Check to see if the earbuds have been put inside the case in the right orientation, and a white light on the earbuds will indicate they are still being charged. This light will go off once the earbud’s have been completely charged.

3.Clean the magnetic connector pins on the case and connector place on the earbuds with a clean cloth with mild alcohol and check the charging of the earbuds again

4.After cleaning, put the left earbud into the case in desired orientation and close the lid.

5.After cleaning, put the right earbud into the case in desired orientation and close the lid.

6. Once both the earbuds are charged, the LED on the case will go off.

1.Check if the charging pins of the case are clear and there is no obstruction.

2.Check if the charging pin of the earbuds are clear and there is no obstruction.

3.Check if the orientation of the earbuds inside the case is correct and they have been properly inserted inside the case.

4.Check if the pogo pins are clean. You may do so by gently cleaning it cotton swabs with alcohol.

1.Check if connected device does not have any equalizer settings applied.

2.Check if the problem still occurs if the device is moved closer and all obstacles in the middle are removed.

3.Check if the distortion or quality lowers at all volumes or only at high volumes.

4.Check the sound on different media players and different devices and if the distortion happens on all devices or only on specific ones.

5.Check if the problem occurs at all levels of charging or only at low charging levels.

6.Check if the earbuds do not have water droplets, in case they do, use the blow dryer to dry out any water from a distance.

7.Check if the earbuds are clogged with ear wax, simply clear the earbuds to restore the original sound.

1.Check if connected device does not have any equalizer settings applied.

2.Check if the problem still occurs if the device is moved closer and all obstacles in the middle are removed.

3.Check if the distortion or quality lowers at all volumes or only at high volumes.

4.Check the sound on different media players and different devices and if the distortion happens on all devices or only on specific ones.

5.Check if the problem occurs at all levels of charging or only at low charging levels.

6.Check if the earbuds do not have water droplets, in case they do, use the blow dryer to dry out any water from a distance.

7.Check if the earbuds are clogged with ear wax, simply clear the earbuds to restore the original sound.

1.Check to see if the device has been properly charged first or not. A blue light on the earbuds will indicate they are still being charged. This light will go off once the earbud’s have been completely charged.

2.Check if the voltage of the charger is correct for the charging case and if the lights on the bottom are glowing to indicate the charge level.

3.Check by switching the earbuds on manually, press and hold the capacitive touch control for 2 seconds until the LED begins to flash in blue.

4.Check if the device was not subject to any mishandling, broken wires or exposed to direct sunlight or hazards like fire.

5.Check if the charging pins of the case and earbuds have some dirt accumulation or corrosion and clean them with alcohol swab and then put them back in the case for charge and the earbuds should start charging.

1.Check if the controls do not work while connected to another device

2.Check if the media player being used supports such controls and if the controls do not function on call or other media players

3.Check if the controls have been physically damaged or exposed to any hazards.

4.Check if the control area has some sweat and oil as that might interfere with the capacitive touch control and clean the control area to remove any oil or sweat and the touch control should start workin

1.Check if restarting the device resolves the issue.

2.Check if dust or ear wax as accumulated near or inside the microphone port, there is no blockage on the microphone.

3.Check if sweat or water has gone inside the microphone.

4.Check if there are any obstructions between the earbuds and the device and clear them, move the device at a closer range to the earbuds and see if it still affects it.

1.Check if restarting the device resolves the issue.

2.Place the earbud’s in the charging case and then try using them again.

3.Try factory-resetting the device.

1.Make sure that you have paired the Airdopes at least once to the device you are trying to use IWP with before.

2.Check if Bluetooth is turned on for your media device and it has the Airdopes in the list of paired devices.

3.Try factory-resetting the device.

4.Check if your Airdopes battery case has battery in it to have IWP functioning.

​

Long tap and hold the CTC on either earbud for 2 seconds to activate the voice assistant

Single press the CTC on either earbud to answer an incoming call and once again to hang up an ongoing call.

Long press the CTC for 2 seconds to reject incoming calls. 

1. While playing music, double tap on the left earbud’s CTC would result in returning to the previous track.

2. While playing music, double tap on the right earbud’s CTC would result in jumping to the next track.

1. When playing music, double press the right earbud’s CTC in order to skip to the next song on the playlist.

2.  When playing music, double press the left earbud’s CTC in order to return to the previous song on the playlist.

Note: Volume cannot be controlled via earbuds and can only be adjusted via phone/media device.

​

1. Our IWP technology allows the earbuds to connect to your phone
if they have already been paired before instantaneously upon opening the case.

2.Simply open the case and ensure that the Bluetooth is turned on for your media device, the buds will connect as soon as the case is opened without the need to take them out of the case first.

There is no special process to enable IWP, simply follow the steps to pair your Airdopes to your media device first, then upon subsequent usage the IWP tech will be enabled automatically and the Airdopes will pair automatically to your previously paired media device if Bluetooth is turned on your media device.

The charging case is ergonomically designed to be portable and lightweight. You can carry your in-ear earbuds around while they’re being charged in the case. The charging case takes around 1-1.5 hours to charge.

No. The volume cannot be controlled via earbuds and can only be adjusted via phone/media device.

Yes, Airdopes 111 supports Type-C charging. If your mobile charger comes with Type-C charging support then you can easily charge your device using your mobile charger.

Yes. Airdopes 111 comes with ASAP Charge technology

Airdopes 111 wireless earbuds offer battery backup of up to 7 hours on a single charge. They also give a total playback time of upto 21 hours along with the charging case.