1.Check when both the earbuds are taken out of the charging case, the earbuds will enter into the Connection Mode, indicated by light blue LED flashes.

2.If one of them fails to smart power on, to manually switch the earbuds on (Manual Power On), long touch the CTC for 3 seconds on both Left and Right earbuds for switching them on until the LED light begins to flash in red and white colours.

3.Place the earbuds in the charging case and then try using them again. Check if it connects automatically.

4.Check and see if hard resetting the device work as desired or not.

5.Check if the earbuds are charging or not. If not then clean the earbuds and the charging case specially the charging pins and connectors with mild alcohol swab and see if it goes in charging mode or not.

​

1.Check if restarting the device resolves the issue.

2.Check if the same problem happens for different devices and media players.

3.Check if there are any obstructions between the earbuds and the device and clear them, move the device at a closer range to the earbuds and see if it still affects it.

4.Try factory-resetting the device.

​Simply the earbuds back in to the case and take them out or perform the factory reset.

​

1. Put the earbuds into the charging case in their correct orientation. 

2. A solid green LED will indicate that the earbuds are being charged. Once Fully charged, the LED indicator turns off.

3. Once both the earbuds are fully charged, the carrying case will switch off to save power.

​

1. Check if the stickers on the charging points of the ear pods are removed or not. If not then it is to be removed and the ear pods will start charging once put inside the charging case.

2. Check if the charging cable connected to the case is not broken, use other charging cable and also ensure that the charger being used is not of 9V or 12V as that will damage the case. The LED lights located on the charging case indicate the battery status of the case.

1.Ensure that the earphone case is charged for charging the earbuds.

2.Check to see if the earbuds have been put inside the case in the right orientation, and a white light on the earbuds will indicate they are still being charged. This light will go off once the earbud’s have been completely charged.

3.Clean the magnetic connector pins on the case and connector place on the earbuds with a clean cloth with mild alcohol and check the charging of the earbuds again.

4.After cleaning, put the left earbud into the case in desired orientation and close the lid.

5.After cleaning, put the right earbud into the case in desired orientation and close the lid.

6.Once both the earbuds are charged, the LED on the case will go off.

​

1.Check if the charging pins of the case are clear and there is no obstruction.

2.Check if the charging pin of the earbuds are clear and there is no obstruction.

3.Check if the orientation of the earbuds inside the case is correct and they have been properly inserted inside the case.

4.Check if the pogo pins are clean. You may do so by gently cleaning it cotton swabs with alcohol.

1.Check if connected device does not have any equalizer settings applied.

2.Check if the problem still occurs if the device is moved closer and all obstacles in the middle are removed.

3.Check if the distortion or quality lowers at all volumes or only at high volumes.

4.Check the sound on different media players and different devices and if the distortion happens on all devices or only on specific ones.

5.Check if the problem occurs at all levels of charging or only at low charging levels.

6.Check if the earbuds do not have water droplets, in case they do, use the blow dryer to dry out any water from a distance.

7.Check if the earbuds are clogged with ear wax, simply clear the earbuds to restore the original sound.

1.Check if connected device does not have any equalizer settings applied.

2.Check if the problem still occurs if the device is moved closer and all obstacles in the middle are removed.

3.Check if the distortion or quality lowers at all volumes or only at high volumes.

4.Check the sound on different media players and different devices and if the distortion happens on all devices or only on specific ones.

5.Check if the problem occurs at all levels of charging or only at low charging levels.

6.Check if the earbuds do not have water droplets, in case they do, use the blow dryer to dry out any water from a distance.

7.Check if the earbuds are clogged with ear wax, simply clear the earbuds to restore the original sound.

1.Check to see if the device has been properly charged first or not. A blue light on the earbuds will indicate they are still being charged. This light will go off once the earbud’s have been completely charged.

2.Check if the voltage of the charger is correct for the charging case and if the lights on the bottom are glowing to indicate the charge level.

3.Check by switching the earbuds on manually, press and hold the capacitive touch control for 2 seconds until the LED begins to flash in blue.

4.Check if the device was not subject to any mishandling, broken wires or exposed to direct sunlight or hazards like fire.

5.Check if the charging pins of the case and earbuds have some dirt accumulation or corrosion and clean them with alcohol swab and then put them back in the case for charge and the earbuds should start charging.

1.Check if the controls do not work while connected to another device

2.Check if the media player being used supports such controls and if the controls do not function on call or other media players

3.Check if the controls have been physically damaged or exposed to any hazards.

4.Check if the control area has some sweat and oil as that might interfere with the capacitive touch control and clean the control area to remove any oil or sweat and the touch control should start workin

1.Check if restarting the device resolves the issue.

2.Check if dust or ear wax as accumulated near or inside the microphone port, there is no blockage on the microphone.

3.Check if sweat or water has gone inside the microphone.

4.Check if there are any obstructions between the earbuds and the device and clear them, move the device at a closer range to the earbuds and see if it still affects it.

1.Check if restarting the device resolves the issue.

2.Place the earbud’s in the charging case and then try using them again.

3.Try factory-resetting the device.

1.Make sure that you have paired the Airdopes at least once to the device you are trying to use IWP with before.

2.Check if Bluetooth is turned on for your media device and it has the Airdopes in the list of paired devices.

3.Try factory-resetting the device.

4.Check if your Airdopes battery case has battery in it to have IWP functioning.

1.  Check if the pairing device has the feature enabled. Google Assistant or Siri should be enabled to use this feature from your device.

2. Please follow the steps carefully, long touch the CTC for 2 seconds and release, this should allow Google Assistant or Siri to pop up on the media screen of the device.Though under some circumstance, this feature may or may not work on some devices which may be restricted by default.

There is no special process to enable IWP, simply follow the steps to pair your Airdopes to your media device first, then upon subsequent usage the IWP tech will be enabled automatically and the Airdopes will pair automatically to your previously paired media device if Bluetooth is turned on your media device.

No. Airdopes 101 does not support aptX technology by Qualcomm.

Airdopes 101 wireless earbuds offer battery backup of up to 3 hours on a single charge. They also give a total playback time of 15 hours along with the charging case.

Yes. You can use any adaptor to charge your Airdopes 101 Made in India charging case.

Place the earbud’s in the charging case and then try using them again. If this does not work, try re-setting the device.