Aavante Bar 2000
2.1 Sound Bar with SubWoofer
Digital Audio Power Amplifier
5.715cm*4 SB + 16.51cm SW
No. of Drivers
SB: 800mV±50mV; SW: 400mV±50mV
45Hz - 20KHz
Signal Noise Ratio
Wireless Technology Type
All Bluetooth Devices
Controls & Connections
Poor Sound Quality
Place your device on a stable platform.
Try to reset the device.
Check if the problem still occurs if the device is moved closer and all obstacles in the middle are removed.
Check if the distortion or quality lowers at all volumes or only at high volumes.
Check for different media players and different devices and if the distortion happens on all devices or only on specific ones.
Check if the problem occurs when connected to different power sockets
Check to see if the device has been properly connected, i.e. the jack is properly inserted into the device for aux, properly connected with the HDMI cable from the unit's HDMI (ARC) slot to the HDMI (ARC) slot on your ARC compatible TV, check if the protective cap of the OPTICAL socket is removed, then connect an OPTICAL cable to the TV’s OPTICAL OUT socket and the OPTICAL socket on the unit, the USB that is connected is functional or if it is connected by Bluetooth then it is paired properly and the blue light is not blinking to indicate it is properly paired in Bluetooth mode.
When using either of the Digital inputs, if there is no audio, try setting the TV output to PCM or connect directly to your Blu-ray/another source, some TVs do not pass-through digital audio, check the TV manual for details.
Your TV may be set to variable audio output. Confirm that the audio output setting is set to FIXED or STANDARD, not VARIABLE. Consult your TV’s user manual for more detailed information.
Check if the device has been properly connected to the power socket and if the problem occurs on all modes of playback. If connected to the TV, ensure that the connections are secure, the TV supports the playback mode and the volume is set properly on the TV.
Check if the device was not subject to any mishandling, or exposed to direct sunlight or hazards like fire.
Short press the “INPUT” button on Sound Bar or remote controller to switch it to BT mode. On your phone search for boAt Aavante 2000 and connect.
Press “INPUT” button to enter AUX/USB/Bluetooth/Optical/Coaxial selection Mode.
Check to see if the device is in pairing mode, after powering it on the LED indicator will blink white.
Check if the speaker is in the range of Bluetooth (usually 10m) and if there are any obstructions in between.
Check if the device being connected to supports Bluetooth connections or not
Check if it is a passcode issue and if so enter 0000 / 1234
Check if the speaker being connected to does have any software issues or not – Check to forget the device on Bluetooth, update the mobile software, if it still does not work try factory resetting the device.
The Amazon Firestick will not connect to the Soundbar. The Sound Bar and the Amazon Firestick would connect separately to the TV.
Use a 3.5mm AUX jack to connect any deviceyou intend to use with the boAt Aavante Bar 2000. Use either the buttons on the SoundBar or the "Input" button on the remote to activate AUX. A Green LED indicator will indicate that AUX mode has been selected.
Playback functions (play/pause/volume/tracks) cannot be adjusted through the SoundBar remote when in AUX mode. It can only be done through the Bluetooth connected device.
Plug in your pendrive after switching the SoundBar ON, the unit will automatically read through the files and begin playing music. The LED indicator will flash pink when in USB mode.
Music playback can be controlled from the buttons on the sound bar- Volume, play/pause, change tracks through the remote.
Simply remove the USB if you wish to exit this mode. You can also utilize the "Input" button on the SoundBar buttons or use the remote to change the mode.
Use an optical cable to connect the soundbar to the TV
Select the Optical mode by pressing the OPT input mode button on the remote controller; once selected the LED displays OP as the input. Then, go to the settings on your TV menu and perform the necessary steps to establish connection via the optical mode.
Note:If you are using a smart TV app, please disable
Dolby or DTS mode on the same as the soundbar does not support them.
Check if restarting the device resolves the issue and if the speaker is in Aux mode by short pressing the ‘Mode’ button.
Check if you have connected the aux cable properly and in the correct orientation on both ends.
Check if the problem persists even after using a different cable or different device to connect to the speaker.
Try to check connecting it with another cable or contact the TV customer care and ask for settings.
Check if the same problem happens for different devices and modes
Cable should be ARC 4K 2.0 version.
Contact the TV customer care in order to change the sound output.
The first port of HDMI should be connected to the ARC.
Other Functional Issues
Ensure your device has Bluetooth mode switched on and is discoverable. Also ensure your device is within 10m range of the unit.
Check to see if the device has been properly charged first or not.
Check if the voltage of the charger is correct for the speaker or not.
Check by switching the speaker on manually, press and hold the power on button for at least 3 seconds.
Check if the device was not subject to any mishandling, broken wires or exposed to direct sunlight or hazards like fire.
Check if the controls do not work while connected to another device.
Check if the device is in aux mode because the buttons will not work in aux mode.
Check if the media player being used supports such controls and if the controls do not function on call or other media players.
Check if the controls have been physically damaged or exposed to any hazards like fire.
Check if restarting the device resolves the issue.
Fully let the speaker discharge and then charge it fully again before use.
Try connecting through a different connection mode or media device.
Change the batteries.
Open the mobile camera and check the Infra-Red rays to know if the remote is working or not.
Check if the LED is blinking or not.
Try to check it with another switch board.
Check if the power cable is working or not.
1. Power OFF the Soundbar as well as the subwoofer.
2. Power ON the Soundbar and subwoofer at the same time.
3. The soundbar will be on standby mode with the “- -“symbol. In Subwoofer the blue light will blink very slowly.
4. Press the O/M Button on the control panel of the soundbar OR the BT button on the remote control until Bluetooth Mode is enabled. (Do not connect any devices to the soundbar via Bluetooth at this stage).
5. Long press the “WPS” button (dedicated) on the backside of the woofer panel till the light starts blinking fast. (Note: Sometimes the woofer would go to the standby mode with the static RED light. Re-perform the entire above process again).
6. The light indicator on the subwoofer will be stable to solid blue. This indicates that the subwoofer and soundbar are paired to each other.
No. Aavante 2000 does not come with Dolby Digital.
Yes. Aavante Bar 2000 can be connected via Bluetooth.
Aavante Bar 2000 offers USB, BT, AUX, Optical, HDMI(ARC), RC modes of connectivity.
The subwoofer offers 80W output.
It comes with a wireless subwoofer.
Yes, it does use HDMI (Arc)/ Optical/ Aux.
Plug in the power cord and the display will light up (Standby mode)
Switch on the soundbar by using power button on soundbar or by using STANDBY button on remote.
After switching on, the default input mode will appear on display
To turn off, press and hold the power button on the Soundbar or the remote for 2 seconds or unplug from wall outlet.
The unit will automatically turn to standby mode when no audio input is received. The Soundbar will wake up from Standby mode when any button is pressed or source input is received.
If the TV or the external unit is disconnected, switch it off.
To switch the unit off completely, remove the main plug from the mains socket.
Please turn the unit off completely to save energy when not in use.
Press the “M ” button repeatedly on the Soundbar or press the INPUT button on the remote control to select the BT, AUX, OPTICAL,COAXIAL, HDMI ARC & USB Mode.
The soundBar has 5 equalizer modes:
The SoundBar has two keyhole slots on the back to enable wall mounting, using the fixings provided or a compatible SoundBar bracket (not supplied).
To power ON the SoundBar, simply plug in the power cord and the Red LED indicator will indicate that it is in standby mode.Below are the LED indicators for all modes
Red: Standby Mode
Blue: Bluetooth Mode
Green: AUX Mode
Pink: USB Mode
To power ON/OFF the SoundBar, simply press and hold the standby button for up to 3 seconds until the LED light indicator changes.
To change the input mode(Bluetooth, AUX, USB) tap the standby button lightly. Each tap will make the mode change once.
Please insert the batteries as indicated below:
A. Remove the battery compartment cover.
B. Insert 2 AAA batteries according to the markings inside the compartment.
C. Close the compartment.
No. The SoundBar does not come with any water protection. Please operate it carefully as even a little sprinkle of water could damage the product.